-
Notifications
You must be signed in to change notification settings - Fork 11
Command
If normally a value is sent from the MiSTer to the Display it's the Corename.
To be able to send "other Data" to the Display we added the "Command Mode".
The "Command Mode" Command's can be used outside the tty2oled script as well (ssh,cli).
The new Command Mode don't need an leading "att" to be sent. Every needed Parameter is included with the command.
The only Command which needs additional Data sent after the Command is the Command for Corechange.
โ The Serial Interface on the Host must be correctly configured before you can use the "Command-Mode". โ
For the examples it's assumed that the MiSTer's Interface for tty2oled is /dev/ttyUSB0.
Command to announce Picture Data which will be send after this Command.
Command: echo "CMDAPD,[Corename]" > /dev/ttyUSB[x]
Example: echo "CMDAPD,llander" > /dev/ttyUSB0
After this command was send from the tty2oled Daemon, Picture Data must be sent
using this bash command: tail -n +4 "${picturefolder}/${1}.xbm" | xxd -r -p > ${TTYDEV}
.
โ This command is similar to "CMDCOR" but the picture is not shown, only transferred.
Show Sorgelig's Cat Icon ๐
Command: echo "CMDBYE" > /dev/ttyUSB[x]
Example: echo "CMDBYE" > /dev/ttyUSB0
Clear the Display
Command: echo "CMDCLS" > /dev/ttyUSB[x]
Example: echo "CMDCLS" > /dev/ttyUSB0
Set Display Contrast
Command: echo "CMDCON,[Parameter]" > /dev/ttyUSB[x]
Parameter-Format: "c"
Example: echo "CMDCON,200" > /dev/ttyUSB0
Parameter | Function |
---|---|
c | Contrast Value 0..255 |
Command to announce Corechange. New Picture Data will be send after this Command.
Command: echo "CMDCOR,[Corename]" > /dev/ttyUSB[x]
Example: echo "CMDCOR,llander" > /dev/ttyUSB0
After this command was send from the tty2oled Daemon, Picture Data must be sent
using this bash command: tail -n +4 "${picturefolder}/${1}.xbm" | xxd -r -p > ${TTYDEV}
.
Enable Over The Air (OTA) Update on the ESP32 for the Upload of an new Arduino Program via Wireless Network.
Command: echo "CMDENOTA" > /dev/ttyUSB[x]
Example: echo "CMDENOTA" > /dev/ttyUSB0
Set Font Direction
Command: echo "CMDFOD,[Parameter]
Parameter-Format: "d"
Example: echo "CMDOFF,1"
Parameter | Function |
---|---|
d | 0=Left to Right (0ยฐ, default), 1=Top to Down (90ยฐ), 2=Right to Left (180ยฐ), 3=Down to Top (270ยฐ) |
Send Data to show Geometric Figures on Display
Command: echo "CMDGEO,[Parameter]" > /dev/ttyUSB[x]
Parameter Format = "g,c,x,y,i,j,k"
Example (Draw): echo "CMDGEO,3,1,10,20,100,20,0" > /dev/ttyUSB0
Example (Clear): echo "CMDGEO,3,0,10,20,100,20,0" > /dev/ttyUSB0
Parameter | Function |
---|---|
g | Geometric Figure 1..10, see Geometric Figure List |
c | Draw Color 0=Clear, 1=Draw, 2=XOR/Invert Pixel |
x | X-Position 0..255 |
y | Y-Position 0..63 |
i | Variable Parameter 1 (Function depends on Geometric Figure) |
j | Variable Parameter 2 (Function depends on Geometric Figure) |
k | Variable Parameter 3 (Function depends on Geometric Figure) |
Geometric Figure List
No | Figure | Used Parameter | Link |
---|---|---|---|
1 | Pixel | x,y | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawpixel |
2 | Line | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawline |
3 | Frame | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawframe |
4 | Box (Filled Frame) | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawbox |
5 | Circle | x,y,i | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawcircle |
6 | Disc (Filled Circle) | x,y,i | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawdisc |
7 | Ellipse | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawellipse |
8 | Filled Ellipse | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawfilledellipse |
9 | Rounded Frame | x,y,i,j,k | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawrframe |
10 | Rounded Box | x,y,i,j,k | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawrbox |
Pixel
x,y = Position of the Dot
Line
x,y = x0,y0 = Line Startpoint, i,j = x1,y1 = Line Endpoint
Frames and Boxes
x,y = Left-Upper-Corner of Frame/Box, i,j = Frame/Box width & height, k = Corner Radius for Geometric Figure 9&10
Circle and Disc
x,y = Center of Circle/Disc, i = Radius
Ellipses
x,y = Center of Ellipse, i,j = Radius in x,y direction
Set Power Save Mode/Switch Display On/Off
Command: echo "CMDOFF,[Parameter]
Parameter-Format: "p"
Example: echo "CMDOFF,1"
Parameter | Function |
---|---|
p | Power Save Mode: 0 =Disabled/Display ON (default), 1 =Enabled/Display OFF |
Reboot/Reset ESP32
Command: echo "CMDRESET" > /dev/ttyUSB[x]
Example: echo "CMDRESET" > /dev/ttyUSB0
Set Display Rotation
Command: echo "CMDROT,[Parameter]
Parameter-Format: "r"
Example: echo "CMDROT,1"
Parameter | Function |
---|---|
r | Display Rotation: 0 =Disabled (default), 1 =Enable 180 degree Rotation |
Show actual loaded Corename on Display
Command: echo "CMDSORG" > /dev/ttyUSB[x]
Example: echo "CMDSORG" > /dev/ttyUSB0
Show Startup Text on Display
Command: echo "CMDSORG" > /dev/ttyUSB[x]
Example: echo "CMDSORG" > /dev/ttyUSB0
Show actual loaded Picture on Display
Command: echo "CMDSPIC" > /dev/ttyUSB[x]
Example: echo "CMDSPIC" > /dev/ttyUSB0
Show a full screen test picture which is included in the Arduino Code
Command: echo "CMDTEST" > /dev/ttyUSB[x]
Example: echo "CMDTEST" > /dev/ttyUSB0
Send Text to be shown on Display
Command: echo "CMDTXT,[Parameter]" > /dev/ttyUSB[x]
Parameter-Format = "f,c,x,y,[Text]
Example: echo "CMDTXT,1,1,50,30,Hello World" > /dev/ttyUSB0
Parameter | Function |
---|---|
f | Text-Output Font Type, see Font list |
c | Draw Color 0=Clear, 1=Draw, 2=XOR/Invert Pixel |
x | Text-Output X-Position 0..255 (SSD1322 Display) |
y | Text-Output Y-Position 0..63 (SSD1322 Display) |
[Text] | Text to write on tty2oled |
โ The text starts at the bottom left of the pixel grid coordinates.
Font list
Font Type No | Font Type | Font Size Width x Height, Size for Character A |
---|---|---|
0 | u8g2_font_luBS08_tf | 11x12, 8 Pixel A, Transparent |
1 | u8g2_font_luBS10_tf | 13x15, 10 Pixel A, Transparent |
2 | u8g2_font_luBS14_tf | 20x22, 14 Pixel A, Transparent |
3 | u8g2_font_luBS18_tf | 26x28, 18 Pixel A, Transparent |
4 | u8g2_font_luBS24_tf | 34x36, 24 Pixel A, Transparent |
5 | u8g2_font_profont12_mf | 6x12, 8 Pixel A, Non-Transparent |
6 | u8g2_font_profont17_mf | 9x17, 11 Pixel A, Non-Transparent |
7 | u8g2_font_profont22_mf | 12x22, 14 Pixel A, Non-Transparent |
8 | u8g2_font_profont29_mf | 16x29, 19 Pixel A, Non-Transparent |
9 | u8g2_font_open_iconic_all_2x_t | 16x16 Icons, Transparent |
10 | u8g2_font_lucasarts_scumm_subtitle_o_tf | Nice 12 Pixel Fon, Transparent |
If normally a value is sent from the MiSTer to the Display it's the Corename.
To send "other Data" to the Display we added the "Command Mode".
The "Command Mode" Commands can be used outside (ssh,cli) the tty2oled script as well.
โ The Serial Interface on the Host must be correctly configured before you can use the "Command-Mode". โ
The "Command Mode" starts by sending "att" (Step 1) to the Display
followed by the "Command" (Step 2) and the "Command-Parameter" (Step 3) if needed.
It's assumed the MiSTer's tty2oled Interface is /dev/ttyUSB0.
Set Display Contrast
Step | Linux Command | Function |
---|---|---|
1 | echo "att" > /dev/ttyUSB0 |
Is needed |
2 | echo "CONTRAST" > /dev/ttyUSB0 |
Enable CONTRAST Mode |
3 | echo "200" > /dev/ttyUSB0 |
Send Display Contrast Value to tty2oled |
Send Picture Data to the Display
Step | Linux Command | Function |
---|---|---|
1 | echo "att" > /dev/ttyUSB0 |
Is needed |
2 | echo "CORECHANGE" > /dev/ttyUSB0 |
Enable CORECHANGE Mode |
3 | tail -n +4 "/path/to/picture.xbm" | xxd -r -p > /dev/ttyUSB0 |
Transfer Picture Data to tty2oled |
Show some Text, without the need to use the tty2oled script, at Position X,Y.
Step | Linux Command | Function |
---|---|---|
1 | echo "att" > /dev/ttyUSB0 |
Is needed |
2 | echo "TEXTOUTXY" > /dev/ttyUSB0 |
Enable TEXTOUTXY Mode |
3 | echo "x,y,f,[Text]" > /dev/ttyUSB0 |
Send [Text] with Font f and Position x,y to tty2oled |
Command Parameter Format "x,y,f,[Text]"
Parameter | Function |
---|---|
x | Text-Output X-Position 0..255 (SSD1322 Display) |
y | Text-Output Y-Position 0..63 (SSD1322 Display) |
f | Text-Output Font Type, see Font list |
[Text] | Text to write on tty2oled |
โ The text starts at the bottom left of the pixel grid coordinates.
Font list
Font Type No | Font Type | Font Size Width x Height, Size for Character A |
---|---|---|
0 | u8g2_font_luBS08_tf | 20x12, 8 Pixel A, Transparent |
1 | u8g2_font_luBS10_tf | 26x15, 10 Pixel A, Transparent |
2 | u8g2_font_luBS14_tf | 35x22, 14 Pixel A, Transparent |
3 | u8g2_font_luBS18_tf | 44x28, 18 Pixel A, Transparent |
4 | u8g2_font_luBS24_tf | 61x40, 24 Pixel A, Transparent |
5 | u8g2_font_profont12_mf | 6x12, 8 Pixel A, Non-Transparent |
6 | u8g2_font_profont17_mf | 9x17, 11 Pixel A, Non-Transparent |
7 | u8g2_font_profont22_mf | 12x22, 14 Pixel A, Non-Transparent |
8 | u8g2_font_profont29_mf | 16x29, 19 Pixel A, Non-Transparent |
9 | u8g2_font_open_iconic_all_2x_t | 16x16 Icons, Transparent |
10 | u8g2_font_lucasarts_scumm_subtitle_o_tf | Nice 12 Pixel Fon, Transparent |
All Data taken from the U8G2 Wiki at https://github.com/olikraus/u8g2/wiki/fntlistall
Draw/Clear Geometric Figures (Pixel, Line, Frame, Box (Filled Frame), Circle, Disc (Filled Circle), Ellipse, Filled Ellipse, Rounded Frame, Rounded Box)
Draw Example
Step | Linux Command | Function |
---|---|---|
1 | echo "att" > /dev/ttyUSB0 |
Is needed |
2 | echo "GEOOUTXY" > /dev/ttyUSB0 |
Enable GEOOUTXY Mode |
3 | echo "3,1,20,10,40,10,0" > /dev/ttyUSB0 |
Draw Frame starting at x=20, y=10 with width=40 and height=10 |
Clear Example
Step | Linux Command | Function |
---|---|---|
1 | echo "att" > /dev/ttyUSB0 |
Is needed |
2 | echo "GEOOUTXY" > /dev/ttyUSB0 |
Enable GEOOUTXY Mode |
3 | echo "4,0,20,10,30,20,0" > /dev/ttyUSB0 |
Clear Box starting at x=20, y=10 with width=30 and height=20 |
Command-Parameter Format is "g,c,x,y,i,j,k"
Parameter | Function |
---|---|
g | Geometric Figure 1..10, see Geometric Figure List |
c | Draw Color 0=Clear, 1=Draw, 2=XOR/Invert Pixel |
x | X-Position 0..255 |
y | Y-Position 0..63 |
i | Variable Parameter 1 (Function depends on Geometric Figure) |
j | Variable Parameter 2 (Function depends on Geometric Figure) |
k | Variable Parameter 3 (Function depends on Geometric Figure) |
Geometric Figure List
No | Figure | Used Parameter | Link |
---|---|---|---|
1 | Pixel | x,y | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawpixel |
2 | Line | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawline |
3 | Frame | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawframe |
4 | Box (Filled Frame) | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawbox |
5 | Circle | x,y,i | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawcircle |
6 | Disc (Filled Circle) | x,y,i | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawdisc |
7 | Ellipse | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawellipse |
8 | Filled Ellipse | x,y,i,j | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawfilledellipse |
9 | Rounded Frame | x,y,i,j,k | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawrframe |
10 | Rounded Box | x,y,i,j,k | https://github.com/olikraus/u8g2/wiki/u8g2reference#drawrbox |
Pixel
x,y = Position of the Dot
Line
x,y = x0,y0 = Line Startpoint, i,j = x1,y1 = Line Endpoint
Frames and Boxs
x,y = Left-Upper-Corner of Frame/Box, i,j = Frame/Box width & height, k = Corner Radius for Geometric Figure 9&10
Circle and Disc
x,y = Center of Circle/Disc, i = Radius
Ellipses
x,y = Center of Ellipse, i,j = Radius in x,y direction
...work in Progress
๐พ ๐พ
๐๏ธ >>Start here<<
๐ฅ MiSTer Installation & Update ๐ฅ
โ History (Updates & Notes)
๐ง Realizing / How does it work
๐ Electrical / PCB's / Tested Hardware
โ๏ธ Arduino HowTo for Windows
๐ Arduino IDE Settings
๐ก OTA (Wireless) Arduino Update
๐ฌ CMD Mode (Greyscale/Adafruit GFX)
๐ฌ Old CMD Mode (Monochrome/U8G2)
๐ผ๏ธ Build Greyscale Pictures (GSC)
๐จ Testing / Troubleshooting
๐ Files and Folders in this Repository
๐ผ๏ธ Gallery
๐ฏ Cardware
๐ Credits and Links