2024-06-17

• Properly decode AksIM-2 warning and error bits
• Make MA732 trimming for off-axis applications actually work
• When encoders are no longer active, stop using them and trigger a fault
• Limit the commanded velocity to something physically achievable
• Fault if a non-reducing gear ratio is configured without overriding
• Default bemf_feedforward to 0.0, and fault if it is configured non-zero without acceleration limits or override

This requires moteus_tool from pypi of 0.3.71 or newer to flash over CAN.

2024-05-20

New capabilities

• The ilimit can now be scaled in addition to kp and kd on a per-command basis. This allows seamlessly switching between position and velocity mode even when an integrative term is configured.
• Electrical power to (or from) the motor is now estimated and reported as servo_stats.power_W and register 0x007

Fixes

• Fix many problems when motor_position.output.sign == -1, including BEMF feedforward and cogging torque compensation
• Produce an error for many more malformed diagnostic mode commands, like d pos 0 0 f1

Compatibility

To flash this firmware, moteus_tool version 0.3.70 or newer is required.

2024-04-30

• Support moteus-c1
• Properly detect board hardware when DC input turn-on slew is very slow

2024-01-06

• Implement servo.max_velocity_slip - this can be used to ensure acceleration limits are obeyed when control is saturated in velocity mode
• Support re-capturing position and velocity while in control mode with the "recapture position and velocity" command

2023-12-15

• Resolve an issue that resulted in fault 33 always being reported on r4.5 and earlier boards

2023-12-14

• Fix a problem that triggered fault 37 if a configured I2C device was disconnected or had an intermittent failure

2023-12-04

Required moteus_tool: >= 0.3.65 (python -m pip install --upgrade moteus)

Major Changes

• Resolve robustness issues that prevented I2C encoders from being used as the commutation or output encoder. Their use for output disambiguation worked reliably before and still does.
• Switch I2C encoder polling rate configuration to be measured in microseconds rather than milliseconds. An up-to-date moteus_tool is required to flash this firmware as a result. It will properly migrate configuration on upgrade.
• When in position-timeout mode, ignore user commands completely. This was always the intended behavior, but became broken with the addition of acceleration and velocity limits. As a result of the defect, commands that resulted in non-zero control velocities could result in user initiated torque.

Minor Changes

• Configure AS5600 encoders to disable their internal filters.
• Improve robustness of the encoder filter by preventing velocities from becoming too large.
• If a hard-fault is triggered, perform a 2-flash pattern on the red LED
• If firmware errors cause data to be written to the 0 page, report the fault as an incrementing counter system_info.mem_fault rather than as a error when attempting to perform conf write.
• Ensure that motor_position configuration is updated to match auxiliary port configuration changes. This mostly means that encoder filter bandwidth limits are properly lowered if the polling rate of auxiliary sensors is decreased.

2023-09-26

• Fault if a stop position is commanded along with velocity or acceleration limits. This never did anything useful, but was often accidentally commanded when using old videos that recommend stop position along with new firmware that has acceleration or velocity limits configured.
• Support CUI AMT21 series RS485 encoders. These can be directly connected to the RS422 port on the moteus-n1, and can be connected to moteus-r4 with an adapter circuit similar to that needed for the AksIM-2.
• Support MA732 SPI encoders on any SPI capable auxiliary port.
• Fix stay within mode when velocity or acceleration limits are enabled. If either were enabled, then the commanded limits were not obeyed.
• Define "target velocity == NaN" to mean "target_velocity == 0.0". Previously NaN here was undefined behavior, and would result in the controller becoming non-functional. Most (maybe all) users who commanded NaN actually wanted to be commanding 0.0 anyways.
• "Index" inputs on auxiliary ports are now handled using an interrupt instead of polling at the control rate. This decreases the minimum required index pulse width from 1/PWM_RATE (~33us for a typical 30kHz pwm rate) to ~1us.

2023-07-25

• Ensure the drive stage is off when entering the bootloader
• A new timeout mode, "10" is now added. This will remain in control mode, come to a controlled stop, then hold position
• Fix AS5048 encoders... previously the low 6 bits were not aligned properly, leaving them effectively as 8 bit sensors
• moteus_tool --zero-offset was broken when applied repeatedly, this now should work
• Fix motor_position reference sources when an output offset or sign is configured
• When an output offset or sign was configured, it was possible to start outside of +- 0.5 * rotor_to_output_ratio, no longer

2023-06-22

• Make motor_position.output.sign=-1 actually work. This has been broken since release 2023-05-31
• The bootloader will now respond with BRS off if the query was sent with BRS off
• The bootloader will attempt to automatically recover from busoff events