Arduino support for almost every classic tinyAVR device! Supports ATtiny 1634, 2313/4313, 24/44/84, 441/841, 25/45/85, 261/461/861, 87/167, 48/88, 43 and 828. Supports programming vis ISP, Serial (Optiboot - all parts with >4k flash, and all parts with 4k flash for which an 8k version is available) or VUSB (Micronucleus - where appropriate)
Development of ATTinyCore is proceeding in the v2.0.0-dev branch.
PLEASE DO NOT SUBMIT PR's AGAINST the "MASTER" BRANCH! YOUR CHANGES WILL BE LOST UPON THE NEXT RELEASE IF YOU DO NEW CHANGES NEED TO GO INTO v2.0.0-dev (which will be my next project after DxCore 1.3.7 release this week)
It's not usable presently due to incomplete work, but that is what all future releases will be made from. Notably, I belive the variant pins_arduino.h files are complete, showcasing both the range of new information available to the core and user code for all parts, and the new, consisitent formatting.
ATtiny26 support looks like it may be coming after all....
Let's use that, not gitter.
Users of 1.6.x versions should use caution with any board manager packages as the handling of dependency versions, at least under 1.6.9, appears to be severely broken, such that installing one packages can break others. For example, DxCore won't work if ATYTinyCore is installed on 1.6.9! - both cores correctly specify their requirements, but the IDE does not use the correct versions of the toochain. It is likely that similar bugs involving other tools also manifest here. Use 1.8.13 or similar recent version if at all possible; if you are unwilling or unable to update your main Arduino IDE version, a "portable" installation is recommended - the separate copy of IDE with portable installation should ensure that what you do in that version does not effect the other version - if you can't use 1.8.13, a portable 1.6.9 version will achieve the same thing, only without the other fixes and improvements that went into the IDE since then.
This core supports the following processors - essentially every "classic" tinyAVR processor that makes sense to use with Arduino. The modern (post-2016 release) tinyAVR parts have their own core, as there is practically zero code at the core level that can be shared with classic parts (in exchange for the cores being totally different, sketches can often be moved between these with little to no effort - not always, but often) Click the processor name for part-specific information:
- ATtiny441, 841 (With or without Optiboot or Micronucleus bootloader)
- ATtiny1634 (With or without Optiboot bootloader)
- ATtiny87, 167 (with or without Optiboot or Micronucleus bootloader)
- ATtiny25, 45, 85 (With or without Optiboot or Micronucleus bootloader)
- ATtiny24, 44, 84 (With or without Optiboot or Micronucleus bootloader)
- ATtiny261, 461, 861 (With or without Optiboot bootloader)
- ATtiny48, 88 (With or without Optiboot or Micronucleus bootloader)
- ATtiny828 (With or without Optiboot bootloader)
- ATtiny2313, 4313 (no bootloader)
- ATtiny43 (no bootloader)
Variants of these are also supported (such as the ATtiny1634R, ATtiny2313A or ATtiny85V)
- tinyAVR 0/1/2-series Modern tinyAVR (with 0, 1, or 2 as next-to-last digit) are supported by my megaTinyCore instead. They are totally different in every way except the "t-word" in the name, and the fact that they're great parts and work well with Arduino.
- ATtiny13/13A are supported by MicroCore by @MCUdude
- ATtiny26 are not supported by any Arduino core. They are the obsolete predecessor to the '261, which itself is ancient). I will accept a PR to add support but will not use my own limited development time for such old and uninspiring parts.
- ATtiny 4/5/10/11 and any other "AVRrc" (reduced core) parts. Try this core
Windows users must install Micronucleus drivers manually If you want to use Micronucleus (VUSB) boards on Windows, you must manually install the drivers - Arduino does not run "post-install" tasks for third party libraries (though I am told they recognized how nonsensical this is - a malicious core could still run whatever commands it wanted to by telling the IDE that was how to compile sketches for these boards - and will be changing this in the future. Note also that the 1.5.0 release does not include working micronucleus upload tool for Windows, this is resolved in 1.5.2.
During the install process it will print the path of a post_install.bat that it skipped running. Running that will install the drivers - it's easiest if you copy/paste it, as after installation the drivers will be located in C:\Users\YourUserName\AppData\Local\Arduino15\packages\ATTinyCore\tools\micronucleus\2.5-azd1\
Or they can be downloaded from the following URL https://azduino.com/bin/micronucleus/Drivers-Digistump(win).zip . Unzip, run the installation batch file.
avrdude: error: could not find USB device with vid=0x16c0 pid=0x5dc vendor=www.fischl.de
product='USBasp'
Vaguely recent versions of AVRdude appear to have dropped a few versions of the firmware. If this is the first time you'd installed something that triggered an update here, you may have problems with AVRdude. The solution, thankfully, is straightforward..
.
- Download Zadig from http://zadig.akeo.ie
- Plug in USBasp
- Start zadig
- Options > List all devices
- Select USBasp from the drop down menu
- Select libusbK(v3.0.7.0) driver
- Click Install
This core includes part specific documentation - click the links above for your family of chips and READ IT These describe issues and "gotchas" specific to certain chips. Be sure to review this documentation!
problems dynamically linking libusb-0.1 on linux can occur if Arduino was installed through the Snap package manager. The Arduino IDE should always be installed from the tarball available from http://arduino.cc, never from a package manager.
There is a bug in the IDE that causes compilation errors with some combinations of boards and submenu options on 1.8.5 and earlier on Windows. The symptom of this is an error ending in something like C:\Users\yourusername\AppData\Local\Temp\arduino_build_131884/..\arduino_cache_186227\core\core_ATTinyCore_avr_attinyx4_LTO_enable,chip_84,clock_8internal,eesave_aenable,bod_disable,pinmapping_anew,millis_enabled,neopixelport_porta_1bc5d2d7fe299bbd4d4a668366e76c74.a: No such file or directory - this is caused by the way it includes all options in the name of the file; where there are many menu options, this will exceed the maximum file name length under windows. This issue impacts many parts on ATTinyCore 1.3.0 and later, and the 841/441 on ATTinyCore 1.2.2 and later. To fix this issue without downgrading ATTinyCore, update to 1.8.6 or later of the IDE - 1.8.13 is STRONGLY recommended
Windows store version sometimes experiences strange issues. The windows store issues are difficult to reproduce on other systems, and no reliable solutions to them are currently known. We recommend using the .zip package or standard installer version of the IDE, not the Windows Store version.
On IDEs prior to 1.8.13, you need to select the correct version of the programmer. In 1.8.13 only these programmers are shown. As of 1.4.2, the (ATTinyCore) note is removed, as 1.8.13 has had excellent uptake (because it lacks new bugs and greatly improves UX)
When using a chip for the first time, or after changing the clock speed, EESAVE or BOD settings, you must do "burn bootloader" to set the fuses, even if you are not using the chip with a bootloader
Problems programming some parts for first time, especially ATtiny841/441 These parts are less forgiving of the SCK clock rate. I'm not sure why USBAsp doesn't seem to be working anymore (it used to, and I haven't changed anything), looking into options there. Arduino as ISP or USBTinyISP SLOW will program without issue.
Chips sold as "ATtiny85" with wrong signature - enable verbose upload output, and it will tell you what sig it actually saw. 0x1e9005 means you got scammed (all 0's or all F's is wiring problem, or bricked chip from choosing clock source that isn't present). Apparently one or more foreign sellers have been remarking the much cheaper ATtiny12 as an 85 and ripping people off on ebay/etc.
free(): invalid next size (normal) error This error is due to a bug in AVRdude ( https://savannah.nongnu.org/bugs/?48776 ) - and it's a spurious error, as when it is displayed, the programming operation has actually completed successfully (you can see for yourself by enabling verbose upload, and noting the successful write before this error is shown. It is unknown under what conditions this error appears, though it has been recorded on a USBTinyISP on Linux when bootloading an attiny88 with optiboot.
When using analogRead(), use the A# constant to refer to the pin, not the digital pin number. Analog channel number (see table in datasheet entry for ADMUX register) can also be used - unlike the official core, you can use analogRead() with the differential ADC channels (for example).
When using I2C on anything other than the ATtiny48/88 you must use an I2C pullup resistor on SCL and SDA (if there isn't already one on the I2C device you're working with - many breakout boards include them). 4.7k or 10k is a good default value. On parts with real hardware I2C, the internal pullups are used, and this is sometimes good enough to work without external pullups; this is not the case for devices without hardware I2C (all devices supported by this core except 48/88) - the internal pullups can't be used here, so you must use external ones. That said, for maximum reliability, you should always use external pullups, even on the t48/88, as the internal pullups are not as strong as the specification requires.
You cannot use the Pxn notation (ie, PB2, PA1, etc) to refer to pins - these are defined by the compiler-supplied headers, and not to what an arduino user would expect. To refer to pins by port and bit, use PIN_Pxn (ex, PIN_PB2); these are #defined to the Arduino pin number for the pin in question, and can be used wherever digital pin numbers can be used. We recommend this method of referring to pins, especially on parts with multiple pinmapping options
All ATtiny chips (as well as the vast majority of digital integrated circuits) require a 0.1uF ceramic capacitor between Vcc and Gnd for decoupling; this should be located as close to the chip as possible (minimize length of wires to cap). Devices with multiple Vcc pins, or an AVcc pin, should use a cap on those pins too. Do not be fooled by poorly written tutorials or guides that omit these. Yes, I know that in some cases (ex, the x5-family) the datasheet doesn't mention these - but other users as well as myself have had problems when it was omitted on a t85.
For low power applications, before entering sleep, remember to turn off the ADC (ADCSRA&=(~(1<<ADEN))) - otherwise it will waste ~270uA
When in power down sleep mode, the clock is stopped - using a slower clock speed does not save power while sleeping I am asked very frequently about using very low clock speeds in low-power applications. Almost invariably, upon further interrogation, the user reveals that they plan to have the part in power-down sleep mode almost all the time. In this case, there is often little to be gained from running at a lower clock speed, since it only effects power use in the brief moments that the chip is awake - even more so because these moments may well be shorter when running at a higher clock speed. Clock speeds below 1MHz can present problems while programming due to the programmer using an SCK clock speed too fast for the target chip running at such a low system clock speed.
When using the WDT as a reset source and NOT using a bootloader remember that after reset the WDT will be enabled with minimum timeout. The very first thing your application must do upon restart is reset the WDT (wdt_reset()
), clear WDRF flag in MCUSR (MCUSR&=~(1<<WDRF)
) and then turn off or configure the WDT for your desired settings. If using the Optiboot bootloader, this is already done for you by the bootloader.
Optiboot Support - serial bootloader for ATtiny441/841, 44/84, 45/85, 461/861, 48/88, 828, 1634, 87, 167 only)
The Optiboot bootloader is included for the ATtiny441, 841, 44, 84, 45, 85, 461, 861, 48, 88, 1634, 828, 87 and 167. For boards with a hardware UART, this runs at 57600 baud at 8 MHz and slower, and 115200 baud above that; for boards without hardware UART, it runs at 19200 baud (on these boards TX/RX pins are the same as the builtin software serial, the ones marked AIN0 (TX) and AIN1(RX)). On boards with hardware serial, the bootloader uses UART0 or the LIN/UART as appropriate (bootloaders that use UART1 for devices that have a second UART are included, prefixed with "ser1" - you must flash them manually or modify boards.txt if you wish to use them). Once the bootloader is programmed, the target can be programmed over serial; the bootloader will run after reset, just like on a normal Arduino. Bootloaders are not included for the 2k-flash versions of these parts - more than a quarter of the available flash would go to the bootloader, and the Arduino abstraction is already severely constrained with just 2k of flash. For these parts, we recommend ISP programming. Clock speeds lower than 1MHz are not supported because the resulting baud rates would be so low that it some serial adapters start having problems talking to them. At 1MHz, uploads are painfully slow. We recommend using the bootloader only at 8MHz or higher. If you are trying to save power, it is usually better to run at 8MHz and put the chip to sleep for most of the time.
The ATtiny441/841, ATtiny1634, ATtiny44/84, ATtiny45/85, ATtiny461/861, ATtiny48/88 and the ATtiny x7-family do not have hardware bootloader support. To make the bootloader work, the "Virtual Boot" functionality of Optiboot is used. Because of this, another vector is used to point to point to the start of the applications - this interrupt cannot be used by the application - under the hood, the bootloader rewrites the reset and "save" interrupt vectors, pointing the save vector at the start of the program (where the reset vector would have pointed), and the reset vector to the bootloader (as there is no BOOTRST fuse). Up until version 1.2.0 of this core, the WDT vector was used for this purpose. In 1.2.0 and later, the EE_RDY vector (which is not used by anything in Arduino-land - the EEPROM library uses a busy-wait) is used instead. If the bootloader was burned with 1.1.5 or earlier of this core, the WDT cannot be used to generate an interrupt (WDT as reset source is fine) - re-burning bootloader with 1.2.0 or later will resolve this.
Virtual boot relies on rewriting the vector table, such that the RESET vector points to the bootloader. This presents a potential issue: If the bootloader starts to write the first page, but then - for some reason - fails (such as a poorly timed reset right after the programming process begins), the page containing the reset vectors will be erased but not rewritten, with the result being that both the sketch and bootloader are hosed resulting in ISP programming being required to revive the chip. See #398
See the Programming Guide for more information on programming parts using Optiboot.
It's finally here! As of 1.4.0, we now offer Micronucleus (aka Digispark) support for some of the more popular boards for these bootloaders. This allows sketches to be uploaded directly via USB, which many users find highly convenient. This comes at a cost in terms of flash - they typically use around 1.5k of flash, and they sometimes have problems connecting to specific USB ports. These boards are available from various vendors; see the part-specific documentation pages for more information on the implementation used on specific parts. For more information on using Micronucleus, see the usage documentation.
Changing the ATtiny clock speed, B.O.D. settings etc, is easy. When an ATTinyCore board is selected from the Tools -> Board menu, there will appear extra submenus under Tools menu where we can set several ATtiny properties:
- Tools > Save EEPROM: (Boards without bootloader only - controls whether EEPROM is erased during a chip erase cycle)
- Tools > Timer 1 clock: (ATtiny25/45/85 only - allows Timer1 to be clocked off the PLL for higher frequency PWM)
- Tools > LTO: (Link Time Optimization makes sketches smaller, but requires AVR boards 1.6.11 or later)
- Tools > B.O.D Level: (trigger voltage for Brown Out Detection - below this voltage, chip will be held in reset)
- Tools > Chip: (Select the part being used )
- Tools > Clock: (Select the desired clock speed)
- Tools > B.O.D. Mode (active): (441, 841, 1634, 828 only - see B. O. D. section below)
- Tools > B.O.D. Mode (sleep): (441, 841, 1634, 828 only - see B. O. D. section below)
After changing the clock source, BOD settings, or whether to save EEPROM on chip erase), you must do "Burn Bootloader" with an ISP programmer. See Programming Guide
Supported clock speeds are shown in the menus in descending order of usefulness, ie, the popular clock speeds/sources are at the top, and the weird ones are at the bottom. See the notes for caveats specific to certain clock speeds.
Internal:
- 8 MHz
- 1 MHz
- 16 MHz (PLL clock, x5, x61 only)
- 16 MHz ‡ (aggressively configured 441/841 only)
- 4 MHz*** (except on x313, starts up at 1MHz and immediately switches to 4MHz before setup() is run)
- 16.5MHz †! (PLL clock, tweaked, x5, x61 Micronucleus only, for USB support)
- 12.8MHz †‡ (Internal, tweaked hardcore, Micronucleus only, for USB support)
- 0.5 MHz** ‼ (x313 only)
- 512 kHz** ‼ (ULP - x41 only)
- 256 kHz** ‼ (ULP - x41 only)
- 128 kHz** ‼ (watchdog or ULP, all except 1643, 828)
- 64 kHz** ‼ (ULP - x41 only)
- 32 kHz** ‼ (ULP - 1634, 828, x41 only)
External crystal (all except 828, 43 and x8-family):
- 20 MHz !
- 18.432 MHz* !
- 16 MHz
- 14.7456 MHz* !
- 12 MHz !
- 11.0592 MHz* !
- 9.216 MHz* !
- 8 MHz
- 7.3728 MHz* !
- 6 MHz !
- 4 MHz
All available clock options for the selected processor will be shown in the Tools -> Clock menu.
*
These weird crystals are "UART frequencies" - these divide evenly to common baud rates, so you can get a perfect match if this is required for your application - typical UART use cases do not require running at one of these UART frequencies, the usual caveats about software serial and baud rate accuracy on classic (pre-2016) AVR designs notwithstanding. These crystal options are not available for chips without a UART in versions of ATTinyCore older than 1.1.5, and are never recommended for parts without a hardware serial port.
**
These options are slow enough that many ISP programmers may not be able to program them. Depending on the ISP programmer (and in some cases the firmware on it), there may be a setting or jumper to slow the SCK frequency down for programming these parts, or it may automatically figure it out. The SCK frequency must be less than 1/6th of the system clock for ISP programming. Before using a such a low clock speed, consider whether you might be able to get lower power consumption by running at a higher base clock while staying in sleep most of the time - this results in fewer programming headaches, and in many (but not all) use cases results in comparable or lower power consumption.
***
The 4MHz internal option is useful if you are running near the minimum voltage - the lowest voltage for most of these parts is 1.8v, and at that voltage, they are only rated for 4MHz maximum. This starts up at 1 MHz and then switches to 4 MHz. Hence, bootloader performance is very slow, as it doesn't (yet) do this itself.
â€
These speeds support USB when used with the internal clock. Available on Micronucleus boards only.
‡
Aggressively tuned internal oscillators have to be slowed down when writing to EEPROM, and then sped back up. We attempt to correct millis timekeeping for this, but you may still see timing glitches. Please report any hangs or other bad behavior you observe with these, as this is a very new feature, and more aggressive measures to prevent CPU glitches may be required.
!
Micros takes longer to return on these clocks (64/clock cycles per microsecond is not an integer).
‼
micros()
and delayMicroseconds()
require a system clock of 1 MHz or higher.
Warning Particularly in versions prior to 1.5.0, When using weird clock frequencies (those other than 16MHz, 8MHz, 4MHz, 2MHz, 1MHz, 0.5MHz), micros() is significantly slower (~ 110 clocks) (It reports the time at the point when it was called, not the end, however, and the time it gives is pretty close to reality). This combination of performance and accuracy is the result of hand tuning for these clock speeds. For other clock speeds (for example, if you add your own), it will be slower still - hundreds of clock cycles - though the numbers will be reasonably accurate, and reflect the time when it was called. millis() is not effected, only micros() and delay().
This differs from the behavior of official Arduino core - the "stock" micros() executes equally fast at all clock speeds, and instead returns wrong values for "weird" clock speeds (64/(clock speed in microseconds, rounded down to integer), rounded down to integer. 12.8 MHz is a special case and is handled exactly.
Thanks to @cburstedde for his work this his work towards making this suck less in the 1.5.0 release!
These parts do not support using an external crystal. External Clock, however, is supported - this requires an external clock source (not just a crystal) connected to the CLKI pin. DANGER if this clock source is not present, you must supply a clock source to CLKI pin before it can be reprogrammed, including to use a different clock source. The external CLOCK option is available through the IDE only for parts which don't support an external crystal. This is not the same as external crystal - do not use this option if you are unsure about the difference between external clock and external crystal! External clock sources are commonly sold as "oscillators", we recommend the KC5032A-series for it's low cost and wide operating voltage range of 1.6~5.5v (ie, the entire operating range of these parts!). Every other oscillator available from Digikey has a narrower voltage range (often 3.3v or 5v +/- 10%, though some work from wider ranges). Through-hole units are available, but expensive, and all have the restrictive supply voltage requirements. If selecting your own oscillator, you want an "XO" type.
The use of an external clock - that is, a single wire with an appropriate clock signal is supplied to the XTAL1 pin from an external source, is possible using this core. This is an advanced feature, and is not supported directly through the IDE (except as noted above) to reduce the risk of people confusing it with external crystal and bricking their chips (if external clock is set as clock source when actually using external crystal, you must supply a clock signal on XTAL1 to program the chip again, including to set it to use a crystal again). To use an external clock:
- Connect the chip, and ensure that the external clock source is present.
- Select the desired clock speed with the external crystal option.
- From File -> Preferences, ensure that "Show verbose output" is enabled for "uploading".
- Connect your ISP programmer.
- Choose "Burn Bootloader". This will set all the selected fuses, only it will be set to use a crystal (this is fine, the external clock will substitute this). However, at this point the XTAL2 pin will not be usable as GPIO.
- Scroll up in the bottom pane of the IDE to the top of the upload output. The first line will be the avrdude command used to burn the bootloader. Copy this into a text editor. If the command includes -e, remove -e and everything after it. If it just points to the bootloader hex file, remove "-Uflash:w:(path to bootloader .hex file):i" from the end of the command.
- Add -Ulfuse:w:0xF0:m to the end of the command.
- Copy/paste this command into a command window, and hit return. Your chip should now be running on the external clock, and the XTAL2 pin (but not the XTAL1 pin) will be available for use normally.
- When compiling for and uploading to your now-externally-clocked part, use the external crystal option corresponding to the clock speed you are using.
The clock speed is made available via the F_CPU #define - you can test this using #if macro
In version 1.3.3 and later, the clock source is also made available via the CLOCK_SOURCE #define. CLOCK_SOURCE can take one of the following values (as of 1.4.0, it is expanded to cover a few weird clocking situations: the low 4 bits identify the source, and high 4 bits identify special things regarding it:
0 - Internal 8MHz oscillator, not prescaled, or prescaled to 1 MHz (ie, fully set by fuses)
1 - External Crystal
2 - External Clock (only available within the core on the 48, 88 and 828, as described above - note that above steps to use external clock on other parts, this will still be 1, not 2; as far as the core knows, it's a crystal)
3 - Internal WDT oscillator (not available on the x41, 1634, and 828)
4 - Internal ULP oscillator (available only on the x41, 1634, and 828)
5 - Internal 4MHz oscillator (present only on the x313 parts - if the 8MHz internal oscillator is prescaled to 4MHz, CLOCK_SOURCE will be 0, not 5)
6 - Internal PLL (x5 and x61 only)
15 or 0x10 (ie, 0x10 | 0) - Internal oscillator with prescaling not set by fuses (ie, not 1 MHz or 8 MHz - ie, 2 or 4 MHz)
17 or 0x11 (ie, 0x10 | 1) - External crystal at 16MHz, which may be prescaled to get lower frequencies (for Digispark Pro ATtiny167)
18 or 0x12 (ie, 0x10 | 2) - External clock at 16MHz, which may be prescaled to get lower frequencies (for MH Tiny ATtiny88)
Instead of referring to pins by the digital pin numbers, it is now (as of 1.4.0) possible to refer to pins based on their port and pin number within the port. We recommend this method of referring to pins in all cases, as it can be more easily cross-referenced with the datasheet, and is independent of pin mapping (for devices with multiple pin mapping options). It also helps to build good mental habits with regards to thinking about pins in the context of ports, which is helpful when writing code where more advanced techniques are needed. For every pin, the core supplies a constant of the form PIN_Pxn
, where x
is the port letter, and n
is the bit of the pin within that port; this is a #define set to the digital pin number corresponding to it. For example, PIN_PA2
refers to bit 2 in PORTA. On the ATtiny167, where there are three different pin mappings, all radically different, analogWrite(PIN_PA2,128)
will always generate a squarewave on the same pin, and the code can be moved between pinmappings without concern.
In version 1.2.2 and later, Sketch -> Export compiled binary will generate an assembly listing in the sketch folder; this is particularly useful when attempting to reduce flash usage, as you can see how much flash is used by different functions.
Link time optimization is enabled by default. If compiling with very old versions of the IDE, this must be disabled. Cases do exist where this setting can change behavior of a sketch; in all cases where this has been observed, a bug in the code was hidden by one setting or the other, and/or undefined behavior was invoked. This is a problem with your code, not the core.
For those who prefer to compile with a makefile instead of the IDE, sketches can be compiled with https://github.com/sudar/Arduino-Makefile - See the makefile documentation for more information on specific steps needed for this process.
You must have external pullup resistors installed - unlike devices with a real hardware TWI port, the internal pullups cannot be used with USI-based I2C to make simple cases (short wires, small number of tolerant slave devices) work. In all cases, including parts with hardware I2C where it may work sometimes, you should always use external pullup resistors, as the internal ones are far weaker than the I2C standard requires for reliable operation.
On the following chips, I2C functionality can be achieved with the hardware USI. As of version 1.1.3 this is handled transparently via the special version of the Wire library included with this core. Be aware that USI-based I2C is not available when USI-based SPI is in use.
- ATtiny x5 (25/45/85)
- ATtiny x4 (24/44/84)
- ATtiny x61 (262/461/861)
- ATtiny x7 (87/167)
- ATtiny x313 (2313/4313)
- ATtiny1634
On the following chips, slave I2C functionality is provided in hardware, but a software implementation must be used for master functionality. This is done automatically with the included Wire library. In versions prior to 1.2.2, USI on these devices is a flash-hog; this has been greatly improved in 1.2.2.
- ATtiny828
- ATtiny x41 (441/841)
On the following chips, full master/slave I2C functionality is provided in hardware and the Wire library uses it:
- ATtiny x8 (48, 88)
On the following chips, full SPI functionality is provided in hardware, and works identically to SPI on Atmega chips:
- ATtiny828
- ATtiny x7 (87/167) (it has both a USI and full SPI, but the SPI library will use the SPI hardware)
- ATtiny x41 (441/841)
- ATtiny x8 (48, 88)
On the following chips, SPI functionality can be achieved with the hardware USI - as of version 1.1.3 of this core, this should be handled transparently via the SPI library. Take care to note that the USI does not have MISO/MOSI, it has DI/DO; when operating in master mode, DI is MISO, and DO is MOSI. When operating in slave mode, DI is MOSI and DO is MISO. The #defines for MISO and MOSI assume master mode (as this is much more common). Clock dividers 2, 4, 8 and >=14 are implemented as separate routines; call SPISettings
or setClockDivider
with a constant value to use less program space, otherwise, all routines will be included along with 32-bit math. Clock dividers larger than 14 are only approximate because the routine is optimized for size, not exactness. Also, interrupts are not disabled during data transfer as SPI clock doesn't need to be precise in most cases. If you use long interrupt routines or require consistent clocking, wrap calls to transfer
in ATOMIC_BLOCK
. Be aware that USI-based I2C is not available when USI-based SPI is in use.
- ATtiny x5 (25/45/85)
- ATtiny x4 (24/44/84)
- ATtiny x61 (262/461/861)
- ATtiny x7 (87/167)
- ATtiny x313 (2313/4313)
- ATtiny1634
On the following chips, full serial (UART) support is provided in hardware, as Serial (and Serial1 for parts with two serial ports):
- ATtiny x313 (2313/4313)
- ATtiny x7 (87/167 - LIN support, including a very fancy baud rate generator)
- ATtiny x41 (441/841 - two UARTs)
- ATtiny1634 (two UARTs)
- ATtiny828
On the following chips, no hardware serial is available, however, a built-in software serial named Serial
is provided to maximize compatibility. This uses the analog comparator pins (to take advantage of the interrupt, since very few sketches/libraries use it, while lots of sketches/libraries use PCINTs). TX is AIN0, RX is AIN1 - This is a software implementation - as such, you cannot receive and send at the same time. If you try, you'll get gibberish, just like using SoftwareSerial. See also the discussion of baud rates.
- ATtiny x5 (25/45/85)
- ATtiny x4 (24/44/84)
- ATtiny x61 (261/461/861)
- ATtiny x8 (48/88)
- ATtiny43
This core is also fully compatible with the usual SoftwareSerial library if you want a software serial port on a different pin - however, you can still only transmit or receive on a single software serial instance at a time - on parts without hardware serial, this includes the builtin software serial "Serial" implementation noted above.
Warning: Internal oscillator and Serial Note that when using the internal oscillator or pll clock, you may need to tune the chip (using one of many tiny tuning sketches) and set OSCCAL to the value the tuner gives you on startup in order to make serial (software or hardware) work at all - the internal clock is only calibrated to +/- 10% in most cases, while serial communication requires it to be within just a few percent. However, in practice, a larger portion of parts work without tuning than would be expected from the spec. That said, for the ATtiny x4, x5, x8, and x61-family I have yet to encounter a chip that was not close enough for serial using the internal oscillator at 3.3-5v at room temperature - This is consistent with the Typical Characteristics section of the datasheet, which indicates that the oscillator is fairly stable w/respect to voltage, but highly dependent on temperature.
The ATtiny x41-family, 1634R, and 828R have an internal oscillator factory calibrated to +/- 2% - but only at operating voltage below 4v. Above 4v, the oscillator gets significantly faster, and is no longer good enough for UART communications. The 1634 and 828 (non-R) are not as tightly calibrated (so they may need tuning even at 3.3v) and are a few cents less expensive, but suffer from the same problem at higher voltages. Due to these complexities, it is recommended that those planning to use serial (except on a x41, 1634R or 828R at 2.5~3.3v, or with a Micronucleus bootloader) use an external crystal until a tuning solution is available.
A tuning sketch is planned for a future version of this core. Progress on this has been made - slowly and fitfully. The current plan is for Optiboot bootloader to be optionally burnable with a "tuning" sketch - this will write the calibration value to the space between the end of the bootloader and the end of flash, and the bootloader will load this value if it is set. ( #139 ) Micronucleus using internal oscillator already does this using the USB clock as a timebase, and loads it before the sketch
All of the supported parts except for the x313-family have an Analog to Digital converter on chip. Single-ended ADC inputs can be read using the ADC channel number or the Ax constant (they can NOT be read using the digital pin number). In addition to the single-ended input channels marked on the pinout diagrams, many also support differential ADC input channels. To use these, simply call analogRead() with the appropriate ADC channel number. To get the ADC channel number, refer to the datasheet - it is listed in the Register Description section of the chapter on the ADC, under the ADMUX register.''
All of the supported parts have hardware PWM (timer with output compare functionality) on at least one pin. See the part-specific documentation pages for a chart showing which pins have PWM. In addition to PWM, the on-chip timers are also used for millis() (and other timekeeping functions) and tone() - as well as by many libraries to achieve other functionality. Typically, a timer can only be used for one purpose at a time.
On all supported parts, timekeeping functions are on timer0. On all parts except the tiny841/441 tone() is on timer1; on 841/441, in version 1.1.6 and later, tone() is on Timer2 to improve compatibility (on 1.1.5 and earlier, tone() is on Timer1 on all parts). This means that reconfiguring timer0 by manipulating it's registers will break millis() and delay(). Using tone() will prevent PWM from working on PWM pins controlled by Timer1 (Timer2 for 841/441), and manipulating it's registers will break tone(). Because tone() is now on Timer2 on the 841/441, you can use tone() at the same time as other libraries that use Timer1 (such as Servo, TimerOne, and many others).
Most of the ATtiny parts only have two timers. The attiny841 has a third timer - but be aware that it's Timer2 is very different from the Timer2 on the atmega328p and most other atmega parts - the '841 has a second 16-bit timer (identical to timer1), while the atmega parts usually have an 8-bit asynchronous timer. This means that libraries designed to use Timer2 on the usual Arduino boards (ex, ServoTimer2) cannot be used with the 841.
The standard NeoPixel (WS2812/etc) libraries do not support all the clock speeds that this core supports, and some of them only support certain ports. This core includes two libraries for this, both of which are tightly based on the Adafruit_NeoPixel library, tinyNeoPixel and tinyNeoPixel_Static - the latter has a few differences from the standard library (beyond supporting more clocks speeds and ports), in order to save flash. At speeds below 16MHz, you must select the port containing the pin you wish to use from the Tools -> tinyNeoPixel Port menu. This code is not fully tested at "odd" clock speeds, but definitely works at 8/10/12/16/20 MHz, and will probably work at other speeds, as long as they are 7.3728 MHz or higher. See the tinyNeoPixel documentation and included examples for more information.
All non-bootloader board definitions have a menu option to control whether the contents of the EEPROM are erased when programming. This only applies to ISP programming, and you must "burn bootloader" to set the fuses to apply this. Because it only applies to ISP programming, it is not available for Bootloader board definitions. On those, EEPROM is never retained, on the reasoning that if you are burning the bootloader to a chip, you are trying to restore it to a "fresh" state.
Brown-out detection continuously monitors Vcc, and holds the chip in reset state (BOR) if the applied voltage is below a certain threshold. This is a good idea with slow-rising power supplies or where it is expected that the supply voltage could droop below the required operating voltage for the frequency it is running at (see the speed grade specification for the part you're using) - without BOD enabled, this can put the chip into a hung state until manually reset. However, BOD increases power consumption slightly, and hence may be inappropriate in low power applications.
The BOD voltage trigger level can be chosen from the tools -> BOD menu. The ATtiny441, 841, 828, and 1634 support independently configuring the BOD mode (active, sampled, disabled) for active and sleep modes (see the applicable datasheet for details). These are configured via the Tools -> BOD Mode (sleep) and Tools -> BOD Mode (active) menus.
In all cases, the selected BOD option(s) is/are configured by the fuses, so after changing these, you must "burn bootloader" to set the fuses.
For Micronucleus boards, only options with are vaguely close to manufacturer's spec and "disabled" are available - since with those parts, we know without a doubt what that the clock speed will be, we know what BOD levels would be appropriate. There's not much point to using BOD if the BOD level is so far below spec that the chip would stop running before it was reached.
The Tools -> millis()/micros() allows you to enable or disable the millis() and micros() timers. If set to enable (the default), millis(), micros() will be available. If set to disable, these will not be available, Serial methods which take a timeout as an argument will not have an accurate timeout (though the actual time will be proportional to the timeout supplied); delay will still work. Disabling millis() and micros() saves flash, and eliminates the millis interrupt every 1-2ms; this is especially useful on parts with very limited flash, as it saves a few hundred bytes.
ATTinyCore will never set lock bits automatically, nor will it set fuses to disable ISP programming (it is intentionally not made available as an option, since after doing that, an HVSP programmer is needed to further reprogram the chip, and inexperienced users would be at risk of bricking their chips this way). The usual workflow when these bits are in use is Set other fuses -> Upload -> Test -> set the lockbits and/or fuses. This can be done from the command line using AVRdude. To expedite the process, you can enable "Verbose Upload" in preferences, do "burn bootloader" (the board and/or programmer does not need to be present), scroll to the top of the output window - the first line is the avrdude command used to burn the bootloader, including the paths to all the relevant files. It can be used as a template for the command you execute to set the fuse/lock bits. Disabling of reset is currently not an option, either - but for bootloader boards, this may change - VUSB bootloaders which disable reset are in widespread use, seemingly without issue. It will never be an option for non-bootloader boards because of the convoluted workflow required.
Note that two pin mappings are supported for some devices to retain backwards compatibility with other cores - the pin mapping may be chosen from a menu.
Note that analog pin numbers (ex A0 ) cannot be used with digitalWrite()/digitalRead()/analogWrite() - all pins have a digital pin number. Analog pin number should only be used for analogRead() - this represents a departure from the behavior used in the official AVR boards. This enables us to expose the advanced ADC functionality available on some of the ATtiny parts with minimal impact, as clearly written code is unlikely to fall afoul of this anyway.
Except for the x5, x4, x61, and x313-family, these are only available in surface mount packages. Breakout boards are available from my Tindie store (these are the breakout boards used for testing this core), which have the pins numbered to correspond with the pin numbers used in this core. Where applicable, all of these assembled boards have the bootloader installed, and all are set to run at the advertised speed (most are available with several speed/voltage combinations).
- 841: Bare boards - Assembled Boards
- 1634: Bare boards - Assembled Boards
- 828: Bare boards Assembled Boards
- x61-family (861/461/261): Bare boards Assembled Boards
- x7-family (167/87): Bare boards Assembled Boards
- x8-family (48/88): Bare boards Assembled Boards
- ATtiny43 (including boost converter) Assembled Boards
- SMD/DIP or DIP ATtiny85 prototyping board
- SMD or DIP ATtiny84 prototyping board
- Some people have problems programming the 841 and 1634 with USBAsp and TinyISP - but this is not readily reproducible. ArduinoAsISP works reliably. In some cases, it has been found that connecting reset to ground while using the ISP programmer fixes things (particularly when using the USBAsp with eXtremeBurner AVR) - if doing this, you must release reset (at least momentarily) after each programming operation. This may be due to bugs in USBAsp firmware - See this thread on the Arduino forums for information on updated USBAsp firmware: http://forum.arduino.cc/index.php?topic=363772 (Links to the new firmware are on pages 5-6 of that thread - the beginning is largely a discussion of the inadequacies of the existing firmware)
- At >4v, the speed of the internal oscillator on 828R, 1634R and 841 parts increases significantly - enough that serial (and hence the bootloader) does not work. Significant enhancements have been made on this front in 1.4.0; reburning bootloader should sort it out.
ATTinyCore itself is released under the LGPL 2.1. It may be used, modified, and distributed, and it may be used as part of an application which, itself, is not open source (though any modifications to these libraries must be released under the LGPL as well). Unlike LGPLv3, if this is used in a commercial product, you are not required to provide means for user to update it. A historical investigation has determined that versions of this core have been released under the LGPLv2.1 in the past - it was an oversight on our part that the license file was omitted from this core previously.
The ATTinyCore hardware package (and by extension this repository) contains ATTinyCore as well as libraries and bootloaders. These are released under the same license, unless specified otherwise. For example, tinyNeoPixel and tinyNeoPixel_Static, being based on Adafruit's library, is released under GPLv3, as described in the LICENSE.md in those subfolders and within the body of the library files themselves.
This does not apply to any tools or third party programs used by ATTinyCore. Installing ATTinyCore through board manager will install and/or update other tool(s) to compile and/or upload code. Those are covered by separate licenses included in their respective archives.
This core was originally based on TCWorld's ATTinyCore, which is in turn based on the arduino-tiny core here: http://code.google.com/p/arduino-tiny/ The ATtiny841 support is based on shimniok's ATtiny x41 core, and the 1634 support on Rambo's ATtiny1634 core.\
@per1234, who has been an invaluable resource for myself and others within the Arduino community, specifically having set up the Travis-based CI testing system (which will cease to be used once the other foot drops wrt. Travis terms) and his years of assistance with board manager releases and more.
The pinout diagrams are created by @MCUdude, who maintains a number of excellent cores for virtually every Microcontroller you might want to use with Arduino as as it has "ATmega" in the name - http://github.com/MCUdude
Many individuals have contributed various fixes and improvements via GitHub - see the contributor list for the full list.