Skip to content
This repository has been archived by the owner on Mar 9, 2019. It is now read-only.

Implement interrupt through both flags and regular interrupt handling services

Notifications You must be signed in to change notification settings

helsouri/External_Interrupts-ECE3731-

Repository files navigation

External_Interrupts-ECE3731-

Summary

I aim to have an ongoing event that happens (flashing green) and then interrupt that event through external inputs.
That is to be achieved through the use of assembly language and an interrupt-driven approach.
This project was divided into two parts a pre lab and a post lab

Files included:

  1. The pdf with details requirements
  2. The detailed pdf report inlcuding procedure and details
  3. The main.asm files for both parts (This is the assembly code) [This will not assebmle without proper configurtion {check #4}]
  4. Both parts as a zip file containing all configurations of board for proper assembling [These also include the main]

    Note that the report contains both parts of the assembly code
    Also note that this is HCS12 assembly and needs the HCS12 board to be flashed on along with CodeWarriors the assembler

INTRODUCTION

Often an external input may trigger a certain event. Your Dragon12 board supports external interrupts on PTH (Port H), which conveniently has switches connected to it. There are two types of switches connected to Port H (as you already know from the previous lab). DIP (dual-inline pin) switches – 8 switches that can set corresponding bits high (up) or low (down). Pushbutton switches – 4 switches on the 4 lower bit positions. These switches are termed “active low”. (The DIP switches on the lower four-bit positions are set high (up) to avoid interfering with the pushbutton switches.) Pressing a pushbutton switch causes a high to low logic transition, which causes an interrupt flag bit to be set since the switches are on Port H, which supports a type of external interrupt called “key-wake-up”. A flag bit can cause an interrupt, if enabled to do so.

ASSIGNMENT

PART A: -interrupt driven interface This program is to have a main program loop and one interrupt service routine.
(i) Main Program Loop:
The main program also has code or calls code to initialize an interrupt on PORT H. The main Program constantly calls a Subroutine that flashes the GREEN LED 10 times on the RGB display at a 2Hz rate as a type of “heartbeat” display. (This means on for 250ms and off for 250 ms.) (You do not need to use the timer subsystem to create the 250 ms delay.) This is done in an endless loop.
(ii) Interrupt Service Routine:
The interrupt service routine responds to an external interrupt on PORT H (PTH). Specifically, your program is written so that any one of the pushbutton switches PH0, PH1 and PH2 can cause an interrupt. (There is one interrupt service routine for PTH which handles all of these switches.) The interrupt service routine determines which switch caused the interrupt, by testing IF flag bits, not the switches and performs the corresponding action for the switch. The Actions are as follows:

PH0:

  • The value of all bits on Port H are read.
  • The four leftmost bits as set by the DIP switch bank, represent a 4-bit counter value for this program.
  • PH0 causes the four leftmost bits on PTH to be written to the four rightmost bits of PORTB (LED's). (PH7-4 are written to PORTB3-0 resp.) The upper 4-bits of PORTB will always be cleared.
  • A message is displayed on LCD that SW0 is pressed.

PH1:

  • The value of the 4-bit counter displayed on PORTB (LED's) is incremented by one.
  • When a value of four ones is reached (1111), the counter rolls over to zero (0000).
  • A message is displayed on LCD that SW1 is pressed.
  • Blue LED flashes 2 times

PH2:

  • The value of the 4-bit counter displayed on PORTB (LED's) is decremented by one.
  • When a value of zero is reached and the counter is decremented, it becomes 1111.
  • A message is displayed on LCD that SW1 is pressed.
  • Red LED flashes 2 times

PARTB: -flag polling interface –no interrupts You have to implement the same functionality as in Part (a) but you are not allowed to use interrupts, but instead polls the interrupt flag bits. This program is a polling flag driven interface between the DIP switch bank and pushbuttons on Port H and the 9S12 CPU. Port H bits 7-4 (upper 4-bits) represent the data inputs. Port H bit 0 (PH0) going high to low sets an interrupt flag. This flag is what is referred to as a Strobe signal indicating a command to input the 4-bit data value from PTH 7-4 as currently set by the DIP switches.

About

Implement interrupt through both flags and regular interrupt handling services

Topics

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published