This project is widely inspired by TiltBridge and Nautilis' iSpindel Relay.
Easiest way to install is through BrewFlasher, project is iSpindHub.
It is basically a receiver to get information from your iSpindels and display it allowing you to use your iSpindel(s) even if you do not have WiFi available in your brew cave.
It also acts as a WiFi repetiter and will push iSpindel information to various services (BrewFather, LittleBock, CraftBeerPi etc).
It's a work in Progress :D
I cannot thank enough Thorrak and lbussy for helping me during my dumb moments.
Check it on in the docs folder !
I will try and list the various screens I have tested and am sure are working (this might lead to multiple releases unless I find an elegant way to have this as a selectable option) I might have to rewrite my code to use a generic library and not a specific one ...
This one is an easy to find on Ali Express and is nice because it plugs directly onto a D1 Mini. Display is square 128*128
/!\ I have not tested it (recently) directly plugged onto the D1 Mini. I used the bottom connection and soldered pins.
| Marking on screen | D1 Mini PIN | Alternative names | Comments |
|---|---|---|---|
| LED | 3.3V | LCD | Could be on 5V if your screen is tolerant |
| GND | GND | G | |
| RST | D2 | ||
| DC | D3 | ||
| MOSI | D7 | SDI | |
| SCK | D5 | ||
| 3V | 3V3 | ||
| CS | D4 |
If you want to use the existing pins at the back of the screen do the following
| Marking on screen | D1 Mini PIN | Alternative names | Comments |
|---|---|---|---|
| D4 | D8 | ||
| G | GND | ||
| D7 | D7 | It might be marked D4. It is the one between D6 and D8 | |
| D5 | D5 | ||
| 3V | 3V3 | ||
| RST | D2 | ||
| D3 | D3 |
find it on Amazon.fr REFERRAL LINK
Display is 160*128
| Marking on screen | D1 Mini PIN | Alternative names | Comments |
|---|---|---|---|
| LEDA | D4 | 8 | Could be on 5V if your screen is tolerant |
| GND | GND | 1 | |
| RES | D2 | 5 | |
| RS | D1 | 6 | |
| SDA | D7 | 4 | |
| SCK | D5 | 3 | |
| VCC | 3V3 | 2 | |
| CS | D8 | 7 |
Find it on Amazon.fr REFERRAL LINK
Red PCB with Red Tab Display is 176*220
| Marking on screen | D1 Mini PIN | Alternative names | Comments |
|---|---|---|---|
| LED | D4 | LCD | Could be on 5V if your screen is tolerant |
| GND | GND | G | |
| RST | D2 | ||
| DC | D1 | RS | |
| MOSI | D7 | SDI | |
| SCK | D5 | ||
| 3V | 3V3 | ||
| CS | D8 |
Find it on Amazon.fr REFERRAL LINK
Another one on amazon REFERRAL LINK For this one, connections are as follow
| Marking on screen | D1 Mini PIN | Alternative names | Comments |
|---|---|---|---|
| VCC | Vin | ||
| GND | GND | ||
| CLK | D5 | ||
| SDA | D7 | ||
| RS | D1 | ||
| RST | RST | ||
| CS | D8 | ||
Red PCB with Red Tab Display is 240*320
| Marking on screen | D1 Mini PIN | Alternative names | Comments |
|---|---|---|---|
| LED | D4 | LCD | Could be on 5V if your screen is tolerant |
| GND | GND | G | |
| RST | D2 | RESET | |
| DC | D1 | RS | |
| MOSI | D7 | SDI | |
| SCK | D5 | ||
| VCC | 3V3 | ||
| CS | D8 |