This repository contains some slightly adjusted versions of the Infinitime application, bootloader and reloader (based on wasp-os), to run on the P8a and P8b (and of course, the PineTime as well) smartwatch.
The P8b has a magnetic charging bay, with the two gold contacts in the center top. The P8a uses a charging clip, with the contacts in the center as well. The PineTime uses a magnetic charging bay, with the contacts shifted to one corner.
The (at least the one I have) P8b uses a different SPI flash chip. The bootloader is configured to accept a range of chips.
In addition, the touch driver is a bit different. The P8 touch driver cannot wake up from sleep mode, so instead the accelerometer is used to detect taps and double taps to wake up. The touch driver configuration set in the factory may also vary. A compile time variable is provided. See the file HardwareVariants.md
for more info.
This firmware fork is able to broadcast the 12-bit accelerometer sensor data using a sampling rate of 200 Hz instead of 10 Hz. A companion Android app to read these values in real-time can be found here: https://github.com/StarGate01/PineTimeAcc .
The P8b watch comes without an external low frequency crystal. This is a problem, because precise timing is required for Bluetooth connections. However, the NRF52 can be configured to use its internal RC clock to generate the low frequency clock.
The wasp-os bootloader as well as the mcuboot bootloader are configured to use this LFRC source. Wasp-os uses the Nordic softdevice, which takes care of properly configuring and calibrating the LF RC source. Mcuboot does not perform any calibration, however it does not require Bluetooth at all.
Usage of the LFRC source in InfiniTime and its Nimble stack is now implemented with proper calibration in my p8b fork.
If you don't want to compile the firmware yourself, you can download binaries on the release page.
Requirements for compilation:
- Linux
- GCC, Build-essentials, Git, Bash, Wget, Unzip
- ARM Cortex toolchain
- NRF52 tools
- Apache Mynewt Newt
- CMake
- Python3 + Pip3
If you use Nix, a flake.nix
is provided.
Run scripts/init.sh
to set up the repositories, do not clone this repo with all recursive submodules. This loads all the required submodules, and downloads the newt and python packages.
Use the scripts in scripts/
, run e.g. build_all.sh moy-ton5
to build all the firmware for the P8b watch. The Wasp reloader factory package will package the builds of mcuboot and the Infinitime minimal recovery loader.
All scripts accept either pinetime
, the moy-
designators, or p8
as the first argument (Default: pinetime
). This argument configures the target hardware platform.
You can change the compile time parameters in build_infinitime.sh
if your smartwatch has a different hardware configuration.
See the file HardwareVariants.md
for detailed configuration options for different watches.
Note: NRF connect sometimes seems to overload the connection, if it fails use another tool listed (or look at https://wiki.pine64.org/wiki/PineTime#Companion_Apps)
In general, sometimes the Bluetooth connection crashes, maybe due to interference. Just try again.
Do this at your own risk
Step 0
- State: Stock P8b (Stock)
- Take a note of your stock firmware identification string. E.g. something like MOY-TFK5-1.7.7. This will not be available after overwriting the bootloader, however knowing it will be useful later when picking the right InfiniTime build, and/or will be useful if your watch is a new variant that we have not seen yet. See also the file
HardwareVariants.md
to figure out which build is right for you.
Step 1
- State: Stock P8b (Stock)
- Process: DFU update using DaFlasher
- Payload:
DaFlasherFiles/DaFitBootloader23Hacked.bin
Step 2
- State: Hacked Bootloader (Three colorful squares)
- Process: DFU update using DaFlasher or NrfConnect
- Payload:
DaFlasherFiles/FitBootloaderDFU2.0.1.zip
Step 3
- State: Fit Bootloader (One square)
- Process: DFU update using DaFlasher or NrfConnect
- Payload:
wasp-os/build-p8/bootloader-daflasher.zip
(P8b variant)
Step 4
- State: Wasp-OS Bootloader (Wasp image)
- Process: DFU update using dfu.py (
scripts/load_wasp_reloader.sh p8
) or NrfConnect (or DaFlasher?) - Payload:
wasp-os/build-p8/reloader-factory.zip
(P8b variant w/ mcuboot & Infinitime recovery loader)
Step 5
- State: Wasp-OS Reloader (Small pinecone)
- Process: Wait for internal flash overwrite (pinecone turns red), then reboot by pressing button long, or it reboots automatically
Step 6
- State: MCUBoot Bootloader (Big pinecone V1.0.0)
- Process: Wait for bootloader to boot recovery installer
Step 7
- State: Infinitime recovery installer (Triangle with progress bar)
- Process: Wait for external flash to be written (progress bar). Reboots automatically
Step 8
- State: MCUBoot Bootloader
- Process: Press button until big pinecone is red. Bootloader then installs recovery image. Wait for reboot.
Step 9
- State: Infinitime recovery (Triangle without progress bar)
- Process: DFU update using dfu.py (
scripts/load_infinitime.sh
) or NRFConnect or GadgetBridge (or DaFlasher?) - Payload:
InfiniTime/build/src/pinetime-mcuboot-app-dfu-1.8.0.zip
Step 10
- State: MCUBoot Bootloader
- Process: Press button until pinecone turns blue, this loads the main app.
Step 11
- State: Infinitime Application (Watchface)
- Process: Verify firmware works, and then confirm firmware valid in settings. (Important, otherwise bootloader reverts to recovery)
Do this at your own risk
For OTA
- State: Broken or empty
- Process: Open watch, flash using SWD, eg. J-Link, then continue from wasp-bootloader
- Payload:
wasp-os/build-p8/bootloader.hex
(P8b variant)
For Development
- State: Development on InfiniTime
- Process: Open watch, flash using SWD, eg. J-Link
- Payload:
InfiniTime/build/src/pinetime-app-1.8.0.hex
(P8b variant without bootloader)
Verify OTA process on sealed watchdoneVerify drivers on genuine PinetimedoneUse LFRC clock instead of SYNT on variants without external LF crystaldoneVerify acceleration sensordoneUpdate mcuboot to latestdoneFix wake from sleepdoneUpdate Infinitime to latest (requires touch driver improvements)doneTest and adjust to P8a watchdoneImplement tap to wake on P8aworkaround- Upstream changes to InfiniTime (WIP: InfiniTimeOrg/InfiniTime#1050)
-
pinetime-mcuboot-bootloader/p8b
at StarGate01/pinetime-mcuboot-bootloader, fork of InfiniTimeOrg/pinetime-mcuboot-bootloader -
InfiniTime/p8b
at StarGate01/InfiniTime, fork of ildar/InfiniTime/p8, fork of InfiniTimeOrg/InfiniTime -
wasp-os
at daniel-thompson/wasp-os -
DaFlasherFiles
at atc1441/DaFlasherFiles.git