RFThings RF210
- https://github.com/XuanMinh201/RF210
- https://github.com/FabienFerrero/SUCA
- https://github.com/RFThings/rfthings-stm32l4
Arduino IDE & ESP32 board tuto
- https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-windows-instructions
- https://randomnerdtutorials.com/installing-esp32-arduino-ide-2-0
- https://randomnerdtutorials.com/getting-started-with-esp32
Other
- https://github.com/NamNamIoT/RAK3172_CANOPUS
- https://github.com/RAKWireless/RAK-APOLLO3-RUI
- https://news.rakwireless.com/stm32wl-custom-firmware-via-arduino-using-rak3172-module-for-lorawan
- https://docs.rakwireless.com/Product-Categories/WisDuo/RAK3172-Module/Deprecated-AT-Command
- https://docs.rakwireless.com/Product-Categories/WisDuo/RAK3172-Module/Low-Level-Development
- https://manuals.plus/lacuna/ls200-sensor-and-relay-manual#axzz8IXdHpl1t
- https://github.com/stevemarple/MicroNMEA
- https://github.com/automote/LTR303
- Download and install the Arduino IDE (at least version v1.6.8)
- Start the Arduino IDE
- Go into File/Preferences Add --> Additional Board Manager URLs --> Add URL
https://github.com/raw/espressif/arduino-esp32/gh-pages/package_esp32_index.json
- Open the Boards Manager. Go to Tools > Board > Boards Manager… --> Search for ESP32 and press install button for the ESP32 by Espressif Systems & Install
- Connect your RF210 board (microUSB port) to your PC USB port (normally Windows will automatically install the driver)
- Download sample sketch from Github --> RF210_RAK3172_bridge
- Unzip and open the file RF210_RAK3172_bridge.ino (note that the file name must be the same as the folder name)
- Open the Boards Manager from the Tools --> Board --> esp32 --> ESP32C3 Dev Module and Select.
- Open the Boards Manager from the Tools --> Port and Select Port (check step 1)
- Open the Boards Manager from the Tools --> USB-CDC on boot --> Enable
- Hold the B_ESP1 (boot) button and press ESP_EN1 (reset) button and release the B_ESP1 (boot) button to enter bootmode.
- Upload Sketch (Ctrl+U)
- After upload sketch, press ESP_EN1 to reboot
- Use Serial Monitor to monitor Serial and send CMD
- Enter AT? and press Enter and see
AT+<CMD>?: help on <CMD>
AT+<CMD>: run <CMD>
AT+<CMD>=<value>: set the value
AT+<CMD>=?: get the value
AT+BOOT R: enter bootloader mode for firmware upgrade
AT+BOOTVER R: get the version of RUI Bootloader
ATZ R: triggers a reset of the MCU
ATR R: restore default parameters
AT+DEBUG RW: set debug log
ATE R: show or hide the AT command input (setting is save & not change after reset)
AT+SN R: get the serial number of the device (max 18 char)
AT+BAT R: get the battery level (volt)
AT+BUILDTIME R: get the build time of the firmware
AT+REPOINFO R: get the commit ID of the firmware
AT+VER R: get the version of the firmware
AT+FIRMWAREVER R: get the Customized version of the firmware
AT+CLIVE R: get the version of the AT command
AT+APIVER R: get the version of the RUI API
AT+HWMODEL R: get the string of the hardware model
AT+HWID R: get the string of the hardware id
AT+ALIAS RW: add an alias name to the device
AT+SYSV R: get the System Voltage
AT+SLEEP W: enter sleep mode for a period of time (ms)
AT+LPM RW: get or set the low power mode (0 = off, 1 = on)
AT+LPMLVL RW: get or set the low power mode level
AT+LOCK R: lock the serial port
AT+PWORD RW: set the serial port locking password (max 8 char)
AT+BAUD RW: get or set the serial port baudrate
AT+ATM R: switch to AT command mode
AT+APPEUI RW: get or set the application EUI (8 bytes in hex)
AT+APPKEY RW: get or set the application key (16 bytes in hex)
AT+APPSKEY RW: get or set the application session key (16 bytes in hex)
AT+DEVADDR RW: get or set the device address (4 bytes in hex)
AT+DEVEUI RW: get or set the device EUI (8 bytes in hex)
AT+NETID RW: get the network identifier (NetID) (3 bytes in hex)
AT+NWKSKEY RW: get or set the network session key (16 bytes in hex)
AT+MCROOTKEY RW: get the Mc Root key (16 bytes in hex)
AT+CFM RW: get or set the confirm mode (0 = off, 1 = on)
AT+CFS R: get the confirmation status of the last AT+SEND (0 = failure, 1 = success)
AT+JOIN RW: join network
AT+NJM W: get or set the network join mode (0 = ABP, 1 = OTAA)
AT+NJS R: get the join status (0 = not joined, 1 = joined)
AT+RECV R: print the last received data in hex format
AT+SEND W: send data along with the application port
AT+LPSEND W: send long packet data (max 1000 bytes)
AT+RETY RW: get or set the number of retransmission of confirm packet data
AT+ADR RW: get or set the adaptive data rate setting (0 = off, 1 = on)
AT+CLASS RW: get or set the device class (A = class A, B = class B, C = class C)
AT+DCS RW: get the ETSI duty cycle setting (0 = disabled, 1 = enabled)
AT+DR RW: get or set the data rate
AT+JN1DL RW: get or set the join accept delay between the end of TX and the join RX window 1 in seconds
AT+JN2DL RW: get or set the join accept delay between the end of TX and the join RX window 2 in seconds
AT+PNM RW: get or set the public network mode (0 = off, 1 = on)
AT+RX1DL RW: get or set the delay between the end of TX and the RX window 1 in seconds (1-15)
AT+RX2DL RW: get or set the delay between the end of TX and the RX window 2 in seconds (2-16)
AT+RX2DR RW: get or set the RX2 window data rate
AT+RX2FQ RW: get the RX2 window frequency (Hz)
AT+TXP RW: get or set the transmitting power
AT+LINKCHECK RW: get or set the link check setting (0 = disabled, 1 = once, 2 = everytime)
AT+TIMEREQ RW: request the current date and time (0 = disabled, 1 = enabled)
AT+LBT RW: get or set the LoRaWAN LBT (support Korea Japan)
AT+LBTRSSI RW: get or set the LoRaWAN LBT rssi (support Korea Japan)
AT+LBTSCANTIME RW: get or set the LoRaWAN LBT scantime (support Korea Japan)
AT+PGSLOT RW: get or set the unicast ping slot periodicity (0-7)
AT+BFREQ R: get the data rate and beacon frequency (MHz)
AT+BTIME R: get the beacon time (seconds since GPS Epoch time)
AT+BGW R: get the gateway GPS coordinate, NetID and GwID
AT+LTIME R: get the local time
AT+RSSI R: get the RSSI of the last received packet
AT+ARSSI R: access all open channel RSSI
AT+SNR R: get the SNR of the last received packet
AT+MASK RW: get or set the channel mask to close or open the channel (only for US915, AU915, CN470)
AT+CHE RW: get or set eight channels mode (only for US915 AU915 CN470)
AT+CHS RW: get or set single channels mode (only for US915 AU915 CN470)
AT+BAND RW: get or set the active region (0 = EU433, 1 = CN470, 2 = RU864, 3 = IN865, 4 = EU868, 5 = US915,
6 = AU915, 7 = KR920, 8 = AS923-1 , 9 = AS923-2 , 10 = AS923-3 , 11 = AS923-4)
AT+NWM RW: get or set the network working mode (0 = P2P_LORA, 1 = LoRaWAN, 2 = P2P_FSK)
AT+PFREQ RW: configure P2P Frequency (Note:This command will be deleted in the future)
AT+PSF RW: configure P2P Spreading Factor (5-12)(Note:This command will be deleted in the future)
AT+PBW RW: configure P2P Bandwidth(LORA: 0 = 125, 1 = 250, 2 = 500, 3 = 7.8, 4 = 10.4, 5 = 15.63, 6 = 20.83,
7 = 31.25, 8 = 41.67, 9 = 62.5 FSK:4800-467000)
(Note:This command will be deleted in the future)
AT+PCR RW: configure P2P Code Rate(0=4/5, 1=4/6, 2=4/7, 3=4/8)(Note:This command will be deleted in the future)
AT+PPL RW: configure P2P Preamble Length (5-65535)(Note:This command will be deleted in the future)
AT+PTP RW: configure P2P TX Power(5-22)(Note:This command will be deleted in the future)
AT+PSEND W: send data in P2P mode
AT+PRECV RW: enter P2P RX mode for a period of time (ms)
AT+ENCRY RW: get or set the encryption status of P2P mode
AT+CAD RW: get or set the Channel Activity Detection status of P2P mode
AT+ENCKEY RW: get or set the encryption key of P2P mode (16 bytes in hex)
AT+CRYPIV RW: get or set the encryption IV of P2P mode (16 bytes in hex)
AT+P2P RW: get or set all P2P parameters
AT+PBR RW: get or set the P2P FSK modem bitrate (600-300000 b/s)
AT+PFDEV RW: get or set the P2P FSK modem frequency deviation (600-200000 hz)
AT+IQINVER RW: get or set P2P IQ inversion (1 = on, 0 = off)
AT+SYNCWORD RW: get or set P2P syncword (0x0000 - 0xffff)
AT+RFFREQUENCY RW: get or set P2P Frequency
AT+TXOUTPUTPOWER RW: get or set P2P Tx Power(5-22)
AT+BANDWIDTH RW: get or set P2P Bandwidth(LORA: 0 = 125, 1 = 250, 2 = 500, 3 = 7.8, 4 = 10.4, 5 = 15.63, 6 = 20.83,
7 = 31.25, 8 = 41.67, 9 = 62.5 FSK:4800-467000)
AT+SPREADINGFACTOR RW: get or set P2P Spreading Factor (5-12)
AT+CODINGRATE RW: get or set P2P Code Rate(0=4/5, 1=4/6, 2=4/7, 3=4/8)
AT+PREAMBLELENGTH RW: get or set P2P Preamble Length (5-65535)
AT+SYMBOLTIMEOUT RW: get or set P2P symbolTimeout (0-248)
AT+FIXLENGTHPAYLOAD RW: get or set P2P fix length payload on/off ( 1 = on, 0 = off)
AT+ADDMULC W: add a new multicast group
AT+RMVMULC W: delete a multicast group
AT+LSTMULC R: view multicast group information
AT+TRSSI RW: start RF RSSI tone test
AT+TTONE RW: start RF tone test
AT+TTX RW: set number of packets to be sent for PER RF TX test
AT+TRX RW: set number of packets to be received for PER RF RX test
AT+TCONF RW: configure LoRa RF test
AT+TTH RW: start RF TX hopping test from Fstart to Fstop, with Fdelta steps
AT+TRTH RW: start RF TX hopping test from Fstart to Fstop, with Fdelta interval in random sequence
AT+TOFF RW: stop ongoing RF test
AT+CERTIF RW: set the module in LoraWAN certification mode (0 = normal mode, 1 = certification mode)
AT+CW RW: start continuous wave
ATC+VER R: VER, Return firmware version
ATC+SHT R: SHT, Return the status of the SHTC3 sensor. 1 if available.
ATC+TEMP R: TEMP, Return the temperature value with 0.01° resolution
ATC+HUM R: HUM, Return the humidity value with 1 % resolution
ATC+KX023 R: KX023, Return the status of the KX023 sensor. 1 if available.
ATC+AX R: AX, Return the value of X acceleration with 0.01G resolution
ATC+AY R: AY, Return the value of Y acceleration with 0.01G resolution
ATC+AZ R: AZ, Return the value of Z acceleration with 0.01G resolution
ATC+LTR R: LTR, Return the status of the LTR - 303 sensor. 1 if available.
ATC+LUMCH0 R: LUMCH0, Return the CHANNEL0 value of the LTR - 303 sensor
ATC+LUMCH1 R: LUMCH1, Return the CHANNEL1 value of the LTR - 303 sensor
ATC+LUM R: LUM, Return the CHANNEL1 value of the LTR - 303 sensor
ATC+GPS R: GPS, Return the status of the GNSS module. 1 if available.
ATC+GPSON W: GPSON, Return the GNSS module power | = 1 : GNSS ON | = 0 : GNSS OFF
ATC+GPSPWR W: GPSPWR, Return the GNSS module power | = 1 : GNSS ON | = 0 : GNSS OFF
ATC+GPSSAT R: GPSSAT, Return the number of available satellite(s)
ATC+GPSTIME R: GPSTIME, Return GPS time in EPOCH format
ATC+GPSLAT R: GPSLAT, Return latitude | Return 0 if coordinate is not available
ATC+GPSLON R: GPSLON, Return longtitude | Return 0 if coordinate is not available
ATC+GPSALT R: GPSALT, Return altitude | Return 0 if coordinate is not available
ATC+GPSNMEA W: GPSON, Activate the NMEA log from GNSS module | = 1 : NMEA ON | = 0 : NMEA OFF
ATC+GPSLOG W: GPSLOG, Activate the results from GNSS module every 5s | = 1 : LOG ON | = 0 : LOG OFF
ATC+GPSDC W: GPSDC, Set GNSS module in duty cycle mode with 30sec sleep | = 1 : DC ON | = 0 : DC OFF
ATC+BAT R: BAT, Return battery voltage in mV | Return 0 if not available
ATC+LDO R: LDO, Return LDO voltage in mV | Return 0 if not available
New RAK3172 custom firmware version (not available)
ATC+GPSCONST R: GPSCONST, Activate Galileo, Beidu, GPS and Glonass constellations