An OctoPrint plugin to allow USB ports to be programmatically turned OFF and ON from within the web interface.
Raspberry Pi 3B: A single-board computer made by the Raspberry Pi Foundation
USB: (abbreviation of Universal Serial Bus) is an industry standard that establishes specifications for cables, connectors and protocols for connection, communication and power supply between personal computers and their peripheral devices.
uhubctl: The underlying program to turn USB power off and on. In addition to Raspberry Pi 2B, 3B and 3B+ it supports other USB hubs - refer to the list of supported devices on uhubctl home page.
- The USB specification was created originally when the Type-A side of a USB cable was the PC and the Type-B side was the device. It was assumed that the PC could always provide power to the device.
- For OctoPi, the Type-A side is the Raspberry Pi 3B with a 5V 2.5A power adapter. It can't be sinking power over to the printer controller board since that's now considered to be the one with beefier power needs. This is often the case when the printer board is powered off and the Raspberry is still powered on. This could lead to the printer's LCD remaining on under these circumstances.
- It is suggested that this sinking of power is causing undervoltage conditions in some cases.
- The typical USB connection has four pins: 5V, ground, transmit and receive. OctoPrint appears to be happy with just the last three of these (as suggested by some users). As they say, though, "your mileage may vary".
- Many people are applying a small strip of tape to the inside of their Type-A connectors to prevent 5V from being felt on the controller (Arduino) board.
- There are other configurations in which the user feels like they want to have programmatic control over providing power to downstream devices.
Rather than rigging up inline switches, applying tape inside the tongue of a USB connector or purchasing specialized male/female adapters which omit the 5V line...
...I thought that I would provide this plugin as a simpler alternative.
This plugin was created to support only the following platforms:
- Raspberry Pi 3B
- Raspberry Pi 3B+
- Raspberry Pi 2B
It is NOT intended to support the following:
- Raspberry Pi 3A+
- Raspberry Pi Compute Modules
- Raspberry Pi 1B+
- Raspberry Pi 1A+
- Raspberry Pi Zero W
- Raspberry Pi Zero
- PCs, Macs, generic Linux workstations or anything else
Also, this plugin is NOT intended to support those of you who wish to plug more than one printer into your Raspberry Pi 3B.
I expect that this plugin would be useful for anyone who needs to remove power which is being sinked over to their printer's LCD panel when their printer board is powered OFF.
The uhubctl
author informs me that internally the Raspberry Pi 2B and 3B cannot individually toggle ports. At best, the gang of four ports can be toggled as a group.
I've just purchased and tested the Raspberry Pi 3B+ thoroughly. It seems to have an odd pairing of one internal hub in two sections. In theory, your printer would be controllable from USB2 and a second smart device from USB3. You may also toggle ALL of the Type A style of USB ports as well from the ALL slider.
For my own printer controller board, toggling the power off prevents any communications from happening (but at least it wouldn't sink power over to it, if this is your intention).
I note that on my own test rig, the Robo 3D printer board includes a jumper to determine how the board is powered. If the jumper is set to "USB", this plugin works as expected to completely power ON/OFF all functions on the board over the USB port although this wouldn't technically work in a real printer given the power limitation. If instead the jumper is set to "5V" then toggling the associated USB port to OFF from this plugin will result in a communication error after the timeout has been reached. Therefore this is not compatible with the normal functioning of this board for the purpose of printing.
It would be useful to stop sinking power to the board when it is powered OFF however.
Popup | Seen in State side panel |
---|---|
![]() |
![]() |
So in some cases, this simply won't work for printing. (A better alternative might be a USB adapter with an inline diode for the 5V line.)
There are five USB ports on the USB hub known as 1-1
in the Raspberry Pi 3B. USB port 1 is the micro USB connection we usually power the board with. The remaining ports 2 through 5 are represented in the interface.
The Raspbian operating system assigns these port numbers not by their physical location in the four-connector arrangement but by the ID of the device during bootup or when the cable is connected.
For this reason, I a not persistently storing your settings for every session because this could get confusing if you add/remove USB devices.
This computer has both a 1-1
and a 1-1.1
hub as seen from lsusb
, for example. The second version has some individual control over the first two smart ports, as seen now in the Settings interface.
At the moment, this plugin does not save the power state for each USB port. Each restart of OctoPrint will basically forget how you last left these and assume that they're all ON.
Install via the bundled Plugin Manager or manually using this URL:
https://github.com/OutsourcedGuru/OctoPrint-USBControl/archive/master.zip
When initially installed, the plugin still needs a script to be run once. The instructions for doing this may be found in the associated Settings page but is also included below.
- Install the plugin (see Setup in the section above)
- Visit the Settings page
- Follow the instructions under the Setup required section there
- For this, you are required to remote into the Raspberry Pi 3B using
ssh
orPuTTY
- Copy/paste the install script into this remote session
- Return back to the OctoPrint Settings page
- Indicate that you have run the script
- Select the Save button at the bottom of the Settings page
- For this, you are required to remote into the Raspberry Pi 3B using
- Restart OctoPrint
- Return to the Settings page (you should see the control sliders now for each USB port)
For an OctoPi installation, the command you are asked to run in Step 3 above would be
sudo ~/oprint/lib/python2.7/site-packages/usbcontrol/bin/install
.
The plugin includes an API for programmatically toggling the ports ON/OFF in a way which is similar to OctoPrint's. You can find/copy your API key under Settings -> API.
POST /api/plugin/usbcontrol HTTP/1.1
Host: example.com
Content-Type: application/json
X-Api-Key: abcdef...
{
"command": "usb2",
"arg2": "on"
}
For USB port 2, the arg2
options are "on" and "off".
The API is similar for the remaining ports. Instead of "usb2" and "arg2", replace these with the appropriate number.
There is a special case for this computer (only) for the API to allow all ports to be toggled ON/OFF.
POST /api/plugin/usbcontrol HTTP/1.1
Host: example.com
Content-Type: application/json
X-Api-Key: abcdef...
{
"command": "all",
"argAll": "on"
}
As of v1.0.7, the installation process of the plugin will automatically add a symlink to /usr/local/bin
for the uhubctl
program so that you can simply run it from the command line if you're into that.
Please do not report a bug if you can't print with the USB power turned OFF. It is assumed that this is the case for most printer controllers. If this does work for you, feel lucky.
By the way, this means the same as "I've just gotten a Communications Error popup with the USB port toggled OFF". This is not meant to be a solution to this problem.
Please do not report a bug if you are plugging more than one printer into your Raspberry Pi 3B at the same time.
Please do not report a bug if you are using a platform that isn't listed in the Compatibility section above.