The 6-Axis Sub-G LongRang Solar Power Asset Tracker collects key information required for asset tracking such as acceleration, angular velocity, temperature, atmospheric pressure, and GPS location, and charges the battery using solar charging.
This is an example that provides quick testing of various service scenarios that require long-distance communication of 1Km or more.
Device can be purchased from the Naver Smart Store.
Purchase Link : naver smart store
You can purchase it by contacting sales@axden.io
MCU | Description |
---|---|
CC1310 | Sub-G SoC |
Sensors | Description |
---|---|
L76 | GPS sensor |
MAX2659 | GPS LNA |
LSM6DSl | 6 Axis Accelerometer, Gyroscope |
MS560702BA03 | Barometric Pressure sensor (Tempeature, Air Pressure) |
Si7201 | Hall Sensor |
SPV1050 | Solar battery charger (Max charge current 80mA) |
Solar | On board |
Battery | 3.7V Lithium Battery |
It is a solar power asset tracker capable of Sub-G communication.
Sub-G wireless communication is performed using CC1310 SoC
It can be turned on and off using Si7201 hall sensor and magnet.
Collect location information using L70+MAX2659 / GPS+LNA.
Charge the battery using the SPV1050 and solar panels built into the board.
Use LSM6DSL to collect acceleration and gyro sensor values.
MS560702 is used to collect information on temperature, air pressure, and altitude.
It operates for 5 years using a battery.
This program is not suitable for mass production and commercialization as an example program.
B2B customers should contact development@axden.io.
For B2B customers, we develop firmware optimized for customers' purposes, such as low power, stabilization, and communication with gateways, for free.
Top | Bottom |
![]() |
![]() |
Pinmap can be found in the file board_define.h
#define LED_RED_GPIO IOID_1
#define LED_BLUE_GPIO IOID_0
#define HALL_SENSOR_GPIO IOID_2
#define BAT_EN_GPIO IOID_7
#define BAT_LEVEL_ADC IOID_6
#define GPS_POWER_EN_GPIO IOID_5
#define I2C_SDA IOID_8
#define I2C_SCL IOID_9
#define UART_RX IOID_4
#define UART_TX IOID_3
Sub-G communication-related settings can be found in the RadioTask.c
file.
EasyLink_Params easyLink_params;
EasyLink_Params_init(&easyLink_params);
easyLink_params.ui32ModType = EasyLink_Phy_5kbpsSlLr;
if (EasyLink_init(&easyLink_params) != EasyLink_Status_Success)
{
SysCtrlSystemReset();
}
EasyLink_getIeeeAddr(mac_address);
if (EasyLink_setFrequency(920000000) != EasyLink_Status_Success)
{
SysCtrlSystemReset();
}
if (EasyLink_enableRxAddrFilter(mac_address, 8, 1)
!= EasyLink_Status_Success)
{
SysCtrlSystemReset();
}
radio_packet_protocol.Packet.company_id[0] = COMPANY_ID >> 8;
radio_packet_protocol.Packet.company_id[1] = COMPANY_ID;
radio_packet_protocol.Packet.device_id[0] = DEVICE_TYPE >> 8;
radio_packet_protocol.Packet.device_id[1] = DEVICE_TYPE;
memcpy(radio_packet_protocol.Packet.mac_address, mac_address, 8);
radio_packet_protocol.Packet.control_number = 0;
SensorTask_registerPacketSendRequestCallback(sendPacketCallback);
while (1)
{
Semaphore_pend(radioAccessSemHandle, BIOS_WAIT_FOREVER);
EasyLink_setRfPower(TX_POWER);
radio_sensor_data_packet_send(radio_packet_protocol);
uint32_t events = Event_pend(radioEventHandle, 0,
RADIO_TASK_EVENT_ALL,
BIOS_WAIT_FOREVER);
if (events == RADIO_TASK_EVENT_ACK)
{
recv_error_count = 0;
}
else if (events == RADIO_TASK_EVENT_ACK_TIMEOUT)
{
recv_error_count += 1;
if (recv_error_count > RECV_ERROR_MAX_COUNT)
{
collection_cycle_timeout_count += 3;
recv_error_count = 0;
}
}
}