-
Notifications
You must be signed in to change notification settings - Fork 112
/
README
109 lines (91 loc) · 5.42 KB
/
README
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
___ _ ___ _
/ __|___ _ _ ___ ___| |___ / __|_____ __ _| |__ ___ _ _ ___
| (__/ _ \ ' \(_-</ _ \ / -_) | (__/ _ \ V V / '_ \/ _ \ || (_-<
\___\___/_||_/__/\___/_\___| \___\___/\_/\_/|_.__/\___/\_, /__/
|__/
___ ___ ___ _
___ | _ \ __/ __|_ _ __ _ __| |__
|___| | / _| (__| '_/ _` / _| / /
|_|_\_| \___|_| \__,_\__|_\_\
Welcome to RFCrack - A Software Defined Radio Attack Tool
VERSION Update: this has been updated to Python3 and should work but there are all
kinds of issues I am running into with firmware versions, sdcc, rfcat
etc which may also effect you.. See the RFCat documentation if you run
into issues.
Developer: @Ficti0n - http://ConsoleCowboys.com
CCLabs: http://cclabs.io
Blog: console-cowboys.blogspot.com
Release Tutorial: https://www.youtube.com/watch?v=H7-g15YZBiI
Reversing Signals With RFCrack: https://www.youtube.com/watch?v=XqKoVFyOst0
Release: 1.5
Hardware Needed: (1 Yardstick or 2 for RollingCode)
YardStick: https://goo.gl/wd88sr
RFCrack is my personal RF test bench, it was developed for testing RF communications
between any physical device that communicates over sub Ghz frequencies. IoT devices,
Cars, Alarm Systems etc... Testing was done with the Yardstick One on OSX, but
RFCrack should work fine in linux. Support for other RF related testing will be
added as needed in my testing. I am currently researching keyless Entry bypasses and
other signal analysis functionality. New functionality will be added in the future with
additional hardware requirements for some advanced attacks.
Feel free to use this software as is for personal use only. Do not use this code
in other projects or in commercial products. I hold no liability for your actions
with this code. Your life choices are your own.
Current supported Functionality:
---------------------------------
- Replay attacks -i -F
- Send Saved Payloads -s -u
- Rolling code bypass attacks -r -F -M
- Targeted -t -F
- Jamming -j -F
- Scanning incrementally through frequencies -b -v -F
- Scanning common frequencies -k
- Compare Live incoming signals to previous signal -k -c -f -u
- Graph Signal -n -g -u
Usage Examples / Attacks:
-------------------------
Live Replay: python RFCrack.py -i
Rolling Code: python RFCrack.py -r -M MOD_2FSK -F 314350000
Adjust RSSI Values: python RFCrack.py -r -M MOD_2FSK -F 314350000 -U -100 -L -10
Jamming: python RFCrack.py -j -F 314000000
Scan common freq: python RFCrack.py -k
Scan with your list: python RFCrack.py -k -f 433000000 314000000 390000000
Incremental Scan: python RFCrack.py -b -v 5000000
Send Saved Payload: python RFCrack.py -s -u ./captures/test.cap -F 315000000 -M MOD_ASK_OOK
With Loaded Config: python RFCrack.py -l ./device_templates/doorbell.config -r
Graph a Signal: python RFCrack.py -n -g -u 1f0fffe0fffc01ff803ff007fe0fffc1fff83fff07
Live Signal Identification and Comparison (Use 2 Console Windows):
-----------------------------------------------------------------
Setup sniffer: python RFCrack.py -k -c -f 390000000
Setup Analysis: python RFCrack.py -c -u 1f0fffe0fffc01ff803ff007fe0fffc1fff83fff07f -n
Useful arguments:
------------------------
-M Change modulation, usually MOD_2FSK or MOD_ASK_OOK
-F Change the frequency used in attacks
-U upper_rssi signal strength value for rolling Code
-L lower.rssi signal strength value for rolling code
-S Change Channel Spacing
-V Change Deviation of modulation
-a Jamming frequency variance from sniffer
-s Send packet from a file source
-d Save your current device settings into a loadable template after attack completes
-l Load previously saved device configuration with attack
-n Your using functionality that does not require a yardstick plugged in
-u Use saved data in your attack
Directories Explained:
----------------------
Saved captures get saved to ./captures directory by default!
Live signal identification captures also saved to ./captures directory in capturedClicks.log
Device templates are saved and loaded to ./device_templates by default
Scanning logs are saved to ./scanning_logs named based on date and time of scanning start
Graph comparison images are saved to imageOutput in 2 formats
- Live: LiveComparison.png will just be written over on each signal Analysis
- Log analysis: Comparison1 Comparison2 format is used and written over on each log analysis
Other Notes:
------------------------
Understand that Rolling code is hit or miss due to its nature with jamming and sniffing
at the same time, but it works. Just use the keyfob near the yardsticks as if you were
stalking your target. It will also require 2 yardsticks, one for sniffing while the other
one is jamming. Yardsticks do not send and receive at the same time.
And a final note, this is my own test bench for doing research and dev, if you have ideas
to make RFCrack better based on realistic use case scenarios, feel free to reach out to me If
the ideas are realistic, well thought out, and re-useable use cases I will implement them.