forked from mcauser/RadioHead
-
Notifications
You must be signed in to change notification settings - Fork 0
/
RHSoftwareSPI.h
90 lines (78 loc) · 3.17 KB
/
RHSoftwareSPI.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
// SoftwareSPI.h
// Author: Chris Lapa (chris@lapa.com.au)
// Copyright (C) 2014 Chris Lapa
// Contributed by Chris Lapa
#ifndef RHSoftwareSPI_h
#define RHSoftwareSPI_h
#include <RHGenericSPI.h>
/////////////////////////////////////////////////////////////////////
/// \class RHSoftwareSPI RHSoftwareSPI.h <RHSoftwareSPI.h>
/// \brief Encapsulate a software SPI interface
///
/// This concrete subclass of RHGenericSPI enapsulates a bit-banged software SPI interface.
/// Caution: this software SPI interface will be much slower than hardware SPI on most
/// platforms.
///
/// SPI transactions are not supported, and associated functions do nothing.
///
/// \par Usage
///
/// Usage varies slightly depending on what driver you are using.
///
/// For RF22, for example:
/// \code
/// #include <RHSoftwareSPI.h>
/// RHSoftwareSPI spi;
/// RH_RF22 driver(SS, 2, spi);
/// RHReliableDatagram(driver, CLIENT_ADDRESS);
/// void setup()
/// {
/// spi.setPins(6, 5, 7); // Or whatever SPI pins you need
/// ....
/// }
/// \endcode
class RHSoftwareSPI : public RHGenericSPI
{
public:
/// Constructor
/// Creates an instance of a bit-banged software SPI interface.
/// Sets the SPI pins to the defaults of
/// MISO = 12, MOSI = 11, SCK = 13. If you need other assigments, call setPins() before
/// calling manager.init() or driver.init().
/// \param[in] frequency One of RHGenericSPI::Frequency to select the SPI bus frequency. The frequency
/// is mapped to the closest available bus frequency on the platform. CAUTION: the achieved
/// frequency will almost certainly be very much slower on most platforms. eg on Arduino Uno, the
/// the clock rate is likely to be at best around 46kHz.
/// \param[in] bitOrder Select the SPI bus bit order, one of RHGenericSPI::BitOrderMSBFirst or
/// RHGenericSPI::BitOrderLSBFirst.
/// \param[in] dataMode Selects the SPI bus data mode. One of RHGenericSPI::DataMode
RHSoftwareSPI(Frequency frequency = Frequency1MHz, BitOrder bitOrder = BitOrderMSBFirst, DataMode dataMode = DataMode0);
/// Transfer a single octet to and from the SPI interface
/// \param[in] data The octet to send
/// \return The octet read from SPI while the data octet was sent.
uint8_t transfer(uint8_t data);
/// Initialise the software SPI library
/// Call this after configuring the SPI interface and before using it to transfer data.
/// Initializes the SPI bus by setting SCK, MOSI, and SS to outputs, pulling SCK and MOSI low, and SS high.
void begin();
/// Disables the SPI bus usually, in this case
/// there is no hardware controller to disable.
void end();
/// Sets the pins used by this SoftwareSPIClass instance.
/// The defaults are: MISO = 12, MOSI = 11, SCK = 13.
/// \param[in] miso master in slave out pin used
/// \param[in] mosi master out slave in pin used
/// \param[in] sck clock pin used
void setPins(uint8_t miso = 12, uint8_t mosi = 11, uint8_t sck = 13);
private:
/// Delay routine for bus timing.
void delayPeriod();
private:
uint8_t _miso;
uint8_t _mosi;
uint8_t _sck;
uint8_t _delayCounts;
uint8_t _clockPolarity;
uint8_t _clockPhase;
};
#endif