-
Notifications
You must be signed in to change notification settings - Fork 13
/
Commands by Onri_Raith EBPG.txt
73 lines (47 loc) · 4.42 KB
/
Commands by Onri_Raith EBPG.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
# Follow these commands in relatively chronological order from top-to-bottom...
# (Anything after a hash symbol are optional codes or important comments).
ce <username>
cd jobs
cjob
subl 1 # command for loading sample holder after pumping down.
pg select holder 3 # command for selecting sample holder label.
mvm
# atc
beamload 1na_300um_table.beam_100 or beamload 0na5_300um_table.beam_100 # for setting SEM beam current (0.5, 1, 5 nanoamps).
beamload 5na_300um_table.beam_100 # other optional command for SEM beam current.
pg measure current or mea_c # for locating Faraday cup (main reference point).
# pg move position 0,-500 --rel
# export PG_MAXROTANGLE=1.039640
# export PG_MAXROTANGLE=0.498428
_________________________________________________________________________________________________________
(options: shape - rectangle or cross [rect or cross], positive or negative tone [pos or neg], position in microns - width and height, & joy marker type)
_________________________________________________________________________________________________________
# 1st command is to locate Faraday cup, followed by real or virtual marker position in (real, measured) microns. The semicolon combines both commands.
# You can also use: pg move position 74101.000,55695.000 or specific coordinate on SEM to move to exact location during troubleshooting. # 82217.300,121140.300 85775.800,121138.900 82215.605,117030.505 85774.395,117029.875
# Replace coordinates below with coordinates that have been recorded during the sample holder calibration & adjustment.
mea_c;pg move position 66574,-31288 --rel # (...1, from C-pattern)
# findmark rp20 # >>>> (type after each marker, then press Enter). # This is used if your sample has pre-existing markers. For bare samples without pre-existing markers, see the next comment.
# record real coordinates from SEM window...
mea_c;pg move position 84601,-31288 --rel # (...4, from C-pattern)
# findmark rp20 # >>>> (type after each joymark, then press Enter). # This is used if your sample has pre-existing markers. For bare samples without pre-existing markers, see the next comment.
# record real coordinates from SEM window...
mea_c;pg move position 66574,-49320 --rel # (...2, from C-pattern)
# findmark rp20 # >>>> (type after each joymark, then press Enter). # This is used if your sample has pre-existing markers. For bare samples without pre-existing markers, see the next comment.
# record real coordinates from SEM window...
mea_c;pg move position 84601,-49320 --rel # (...3, from C-pattern)
# findmark rp20 # >>>> (enter after each joymark, then press Enter). # This is used if your sample has pre-existing markers. For bare samples without pre-existing markers, see the next comment.
# record real coordinates from SEM window...
_________________________________________________________________________________________________________
(option: writejob)
# a neat technique for recording coordinates below, involves typing in the last 3 numbers after the decimal (to the right of the decimal, followed by entering the remaining numbers to the left of the decimal.
# (Use this to record SEM coordinates prior to performing "joyplus")
# "joyplus" marker instructions (be sure to gradually zoom in to the desired joymarker locations on the chip):
joyplus >> follow prompt to center desired marker locations on SEM window.
pg move (coordinates, e.g. 85754.200,121167.850) - (remember to press Enter and not q).
job OJB_400_Qubits.job 3 0 83174.000,49980.000 101201.000,49980.000 83174.000,31948.000 101201.000,31948.000 # this is an example.
(find each marker manually upon 2nd prompt to center marker locations on SEM window - this is a confirmation)
Press Enter for each confirmed coordinate (it should result in a "found" joymarker).
# After entering real coordinates, enter the job command as shown above >> after the command runs, there will be a prompt that will allow you to use the built-in SEM to confirm or adjust the location of virtual, joy markers >> let exposure run.
# Here's an example for magnetic tunnel junctions Onri_NanoMTJ_Array_RuO2_01_MTJ_Chip_Full.job
# (these numbers/coordinates are configured like a Z-pattern, taken from SEM coordinates in order, as opposed to the C-pattern that was recorded with the digital microscope, instead of 1-2-3-4, it goes 1-4-2-3)
subu 1 # command to unload the sample holder from the lithography equipment, proceed to vent the vacuum chamber.